summaryrefslogtreecommitdiff
path: root/src/product
Commit message (Collapse)AuthorAge
* altos: Add generic LED driver.Keith Packard2018-10-13
| | | | | | | | | | | This driver uses the generic GPIO functions and allows per-LED port and pin configuration. It supports up to 32 LEDs. Rename SoC-specific LED drivers. Remove enabled parameter to ao_led_init Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Use stdbool true/false instead of TRUE/FALSEKeith Packard2018-10-13
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove 8051 address space specifiersKeith Packard2018-10-13
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove *_TO_DATA macrosKeith Packard2018-10-13
| | | | | | Now that we don't support 8051, we don't need these Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove cc1111 productsKeith Packard2018-10-13
| | | | | | We're not testing these anyways; building new firmware for them is not helpful. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/flash-loader: On STM, don't include ao_usb_disableKeith Packard2018-04-26
| | | | | | This saves a bit of space, keeping the flash loader under 4k on fox Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Move 'ao_force_freq' to ao_config.cKeith Packard2017-05-04
| | | | | | Instead of having to add it to each product using this variable. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/micropeak: Update ao_micropeak.h for MicroPeak v2Keith Packard2017-04-28
| | | | | | Allow different sample times, add constant for MicroPeak v2 log files. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/micropeak: Use existing ao_ms5607_current variableKeith Packard2017-04-28
| | | | | | Instead of defining another. Signed-off-by: Keith Packard <keithp@keithp.com>
* Switch from GPLv2 to GPLv2+Keith Packard2016-07-12
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Replace ao_alarm/ao_clear_alarm with ao_sleep_forKeith Packard2015-02-13
| | | | | | | | | | | | | | | | Having arbitrary alarms firing in the middle of complicated device logic makes no sense at all. Therefore only correct use of ao_alarm and ao_clear_alarm was around a specific ao_sleep call, with correct recovery in case the alarm fires. This patch replaces all uses of ao_alarm/ao_sleep/ao_clear_alarm with ao_sleep_for, a new function which takes the alarm timeout directly. A few cases which weren't simply calling ao_sleep have been reworked to pass the timeout value down to the place where sleep *is* being called, and having that code deal with the return correctly. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Have MicroKite just start recording at startupKeith Packard2014-08-14
| | | | | | | This avoids having MicroKite try to detect boost and has it just start recording data immediately. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Use 32-bits for flight state data (alt/speed/accel)Keith Packard2014-07-10
| | | | | | | Stores 32-bits for all of the flight parameters. Uses 64-bit intermediates for kalman computation. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add support for the "kite" micropeak variantKeith Packard2014-07-06
| | | | | | | This uses a 100m 'launch detect' altitude and logs data every 19.2s instead of every .192s. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Stop sticking cc1111 firmware in src directoryKeith Packard2014-07-05
| | | | | | This just clutters src. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Move ao_tracker.c to kernelKeith Packard2014-06-07
| | | | | | Doesn't make sense to be in product Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Force telemetry on by default for v0.3 TeleGPS boardsKeith Packard2014-06-05
| | | | | | | These don't have a USB connect indicator, so just turn on telemetry by default Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add AO_LOG_FLIGHT packet to TeleGPS logsKeith Packard2014-06-05
| | | | | | This encodes the flight number for tracking of data files. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add debug to tracker to force launchKeith Packard2014-06-05
| | | | | | This lets us test the move from pad to drogue state Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: tracker distance computation flipped arguments aroundKeith Packard2014-06-05
| | | | | | ao_distance takes (lat, lon, lat, lon) not (lat, lat, lon, lon) Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fix tracker start stateKeith Packard2014-06-05
| | | | | | | | | Make sure log can start by scanning existing logs Enable RDF by default Turn off telemetry until we decide whether to turn it on in the loop Allow TeleGPS v0.3 to run without ADC Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Have tracker average 5 GPS samples before moving to pad modeKeith Packard2014-06-05
| | | | | | Avoids early GPS noise right after lock Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Change tracker not-moving speed to 2m/s and documentKeith Packard2014-06-05
| | | | | | Just adjust to avoid sensing motion from GPS noise Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add tracker task for TeleGPSKeith Packard2014-06-05
| | | | | | | This replaces the flight code to monitor GPS state and switch flight states between startup/pad/drogue Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/flash-loader: Check memory addresses against flash spaceKeith Packard2014-05-12
| | | | | | | | | | | This validates memory read/write requests to make sure they are within the available flash memory space. This also reports the flash base and bounds addresses in the 'version' command so that the loader can validate the image before attempting to write it. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add 'microwater' productKeith Packard2014-04-11
| | | | | | | This is a custom firmware spin for micropeak designed for use with water rockets that sets the boost detect altitude to 10m instead of 30m. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Rename 'core' to 'kernel'Keith Packard2014-04-05
| | | | | | | core remains a bad name to use -- dirvish skips files (and directories, it seems) with that name. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Enable system timer in flash loader and prod watchdog with itKeith Packard2014-02-08
| | | | | | | This makes it possible to reflash the board without needing to disable the watchdog. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Clean up warnings for LPC productsKeith Packard2013-12-20
| | | | | | Unused varibles, functions and parameters. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Merge GPS logging into a single functionKeith Packard2013-10-14
| | | | | | | | | | | | Create a new global, ao_gps_new, which indicates new GPS position and satellite data. Use ao_gps_new as the new sleep/wakeup address. Merge the separate gps position/satellite logging tasks into a single function which waits for new data and writes out the changed values. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/micropeak: Increase boost detect to 30mKeith Packard2013-10-13
| | | | | | | | | | | | | This meant increasing the data buffering as well so that we could reliably capture the flight data back to the ground, even for slow flights. And, with the buffer extra large, we work backwards from the current buffer location to find the last ground location rather than working forwards from the first buffered location. This ensures that we don't capture noise before boost and instead capture a nice flight curve instead. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Stop copying cc1111 binaries to the altos/src dirKeith Packard2013-09-15
| | | | | | Just clutters up that directory. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Move micropeak sources aroundKeith Packard2013-09-15
| | | | | | | | This sticks the micropeak sources in appropriate directories, rather than in the micropeak product directory so that they can be shared with future micropeak-style products. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Not all products have pins to control flash loaderKeith Packard2013-09-02
| | | | | | TeleGPS has no exposed pins for this function Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/lpc: Add boot loaderKeith Packard2013-06-24
| | | | | | Support the USB boot loader, add USB pull-up support. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Create per-product flash loadersKeith Packard2013-05-07
| | | | | | | Split the flash loader prototype into pieces so that each product can build a custom flash loader with very little code. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Call ao_task_init before initializing any driversKeith Packard2013-05-07
| | | | | | | | When using task queues, the sleep queues must be initialized before any invocation of ao_wakeup or the OS will crash. Just make sure ao_task_init is always invoked early in the task process to get that done. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Create telebt-v1.0 product. Remove old telebt productsKeith Packard2013-04-08
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add telescience-pwm productKeith Packard2012-10-16
| | | | | | Split out special PWM-sampling telescience product Signed-off-by: Keith Packard <keithp@keithp.com>
* first work on PWM input to TeleScience, 'p' command displays timer 1Robert Garbee2012-10-16
|
* Revert "first work on PWM input to TeleScience, 'p' command displays timer 1"Keith Packard2012-09-01
| | | | | | PWM bits not suitable for master This reverts commit e93c6bcc799d76d4ff425815e2601a25e6796229.
* altos: telelaunch doesn't need ao_radio_cmac_initKeith Packard2012-08-24
| | | | | | | | This function was used to initialize the LCO functions, which were moved to ao_lco.c a few commits back, so ao_radio_cmac_init doesn't even exist anymore. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add ability to re-play telemetry through TeleDongleKeith Packard2012-07-29
| | | | | | | | This adds a new command to TeleDongle to send arbitrary data, and then creates a new tool, 'ao-send-telem' that replays existing telemetry files through TeleDongle. Signed-off-by: Keith Packard <keithp@keithp.com>
* first work on PWM input to TeleScience, 'p' command displays timer 1Robert Garbee2012-07-17
|
* altos: Enable pyro channel control in telepyroKeith Packard2012-07-16
| | | | | | This should make the board actually work now. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Create macros to convert from/to radio RSSI representationKeith Packard2012-07-11
| | | | | | | | AO_RSSI_FROM_RADIO and AO_RADIO_FROM_RSSI. Removes a bunch of open-coded versions of the same function. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Have 'make clean' remove all programs, even old onesKeith Packard2012-07-11
| | | | | | | This makes sure that changing version numbers doesn't leave old compiled output lying around. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Force 434.550Mhz by connecting debug gnd and clk (trac #41)Keith Packard2012-07-10
| | | | | | | | Check for pin P2_2 low at startup and set the frequency to 434.550MHz. This value won't get written to flash, so rebooting again will restore the configured frequency. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Rename *_mm.c back to *.cKeith Packard2012-07-10
| | | | | | Was just a temporary hack to keep cc1111 products building during MM development. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make cc1111 products all depend on ao_arch.h and ao_arch_func.hKeith Packard2012-06-04
| | | | | | Ensures that files get recompiled as needed Signed-off-by: Keith Packard <keithp@keithp.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-12-25 07:25:16 +0000