| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
| |
We're not testing these anyways; building new firmware for them is not helpful.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
Allow the ground software to know which TeleMini version is in use,
even though they are very similar with only ADC values differing.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
There's not enough memory for this command, and it isn't necessary.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
Stores 32-bits for all of the flight parameters. Uses 64-bit
intermediates for kalman computation.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
use the smaller pa to altitude table to make room for the new code
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
This lets the radio code adjust the telemetry packet sending pattern
when the data rate changes.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
Not enough flash otherwise.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
Now that there's space for this, add it in.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
|
|
| |
This lets you directly set the mid-range beep tone; the high and low
tones remain set off of that in the same ratio as before.
Note that none of the cc1111 products get this feature as they don't
have enough flash space anymore...
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
This works on everything with a beeper except TeleMetrum v1.0 which
just doesn't have enough flash space for the code.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
Same data, but EasyMini uses a 3.0V supply while TeleMini uses 3.3V,
which changes the intepretation of all of the ADC values
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
If the MISO line goes low before we manage to configure the
interrupts, we'll miss it entirely unless we check the pin explicitly.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
The ADC code is responsible for actually inserting the non-ADC data
into the ring, so do the copy there.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
The Tm v2 ADC code was not actually fetching and storing the ADC
conversion values.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
Needed for TeleMini v2.0
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
No longer builds like this
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
Mash lots of storage locations and code around to shrink stuff down to size
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
Signed-off-by: Keith Packard <keithp@keithp.com>
|
