blob: 6e6078d6f72d1ab115bcbdbaf27333483464408b (
plain) (
blame)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
|
# TeleMini
This is a very small, baro-only recording dual-deploy altimeter for
model rocketry with integrated telemetry link.
Version 3.0 is in production now and should be available after April
1, 2017.
Production units will be available from the [Garbee and
Garbee](http://shop.gag.com) web store.
For the latest TeleMini firmware and related ground station software, please
visit the [AltOS](../AltOS) page on this site.
Here's a photo of a v3.0 prototype:
<a href="v3.0/telemini-v3.0.jpg"> <img src="v3.0/telemini-v3.0-640.jpg"></a>
## Features ##
### User View ###
* Recording altimeter for model rocketry
* Supports dual deployment (can fire 2 ejection charges)
* 70cm ham-band transceiver for telemetry downlink
* Barometric pressure sensor good to 100k feet MSL
* Designed to use a single LiPo rechargeable battery
* 512kB flight data storage
* 1.7 x 0.5 inch board designed to fit inside 18mm airframe coupler tube
### Developer View ###
* Hardware Features
* [ST STM32F042G6](http://www.st.com/content/st_com/en/products/microcontrollers/stm32-32-bit-arm-cortex-mcus/stm32f0-series/stm32f0x2/stm32f042g6.html) system on chip
* ARM Cortex-M0 MCU
* 32k Flash
* 6k RAM
* USB 2.0
* digital I/O
* [Measurement Specialties MS5607](http://www.te.com/usa-en/product-CAT-BLPS0035.html) pressure sensor
* Software Features
* Written mostly in C with some ARM assembler
* Tools Used
* [gEDA](http://www.gpleda.org/) for schematic capture and PCB layout
* [SDCC](http://sdcc.sourceforge.net/) compiler and source debugger
* Licenses
* The hardware is licensed under the [TAPR](http://www.tapr.org) [Open Hardware License](http://www.tapr.org/ohl.html)
* The software is licensed [GPL version 2 or later](http://www.gnu.org/licenses/old-licenses/gpl-2.0.html)
## Older Versions ##
[Version 1.0](v1.0). Same width (0.5 inches), but doesn't have the
rear two mounting holes so it's a bit shorter (1.5 inches instead of
1.67 inches).
## Artifacts ##
There is a single manual for TeleMini and all other Altus Metrum products,
which is available in [html](../AltOS/doc/altusmetrum.html) and
[pdf](../AltOS/doc/altusmetrum.pdf) formats.
An outline of the board with drill hole locations is available in
[pdf](../Documents/telemini-v3-outline.pdf) format.
The hardware design files can be found on [git.gag.com](http://git.gag.com)
in the project [hw/telemini](http://git.gag.com/?p=hw/telemini;a=summary).
|
