summaryrefslogtreecommitdiff
path: root/src/stm
Commit message (Expand)AuthorAge
...
* altos: Enable STM SYSCFG when routing EXTIKeith Packard2012-08-28
* altos: No need to initialize EXTI priorities at startup timeKeith Packard2012-08-28
* altos: Expose a signed version of the tick countKeith Packard2012-08-27
* altos: Provide interface for STM LCD driver.Keith Packard2012-08-27
* altos: Trigger sample complete when all data are readyKeith Packard2012-08-26
* altos: Shrink STM stack sizeKeith Packard2012-08-26
* altos: Allow STM SPI bus on multiple pin setsKeith Packard2012-08-18
* altos: Add button driver and event queueKeith Packard2012-08-06
* altos: Add ao_gpio_get and ao_exti_set_modeKeith Packard2012-08-06
* altos: Add driver for STM internal flashKeith Packard2012-07-29
* altos: Add software AES implementationKeith Packard2012-07-29
* altos: Place STM config values at fixed addresses for re-useKeith Packard2012-07-17
* altos: Make ao_tick_count visibleKeith Packard2012-07-16
* src: Add explicit 'pin' argument to ao_enable_outputKeith Packard2012-07-14
* altos/stm: Expose ao_gpio_set which sets a specific GPIO pinKeith Packard2012-07-14
* stm: running out of memory in MM -- reduce stack to 668 bytesKeith Packard2012-07-14
* altos/stm: Force STM stack to start at the top of RAMKeith Packard2012-07-14
* altos: Increase default STM stack to 648 bytesKeith Packard2012-06-27
* altos: Clean up STM I2C clock computationsKeith Packard2012-06-27
* altos: get MPU6000 I2C link working reliablyKeith Packard2012-06-27
* altos: reorder stm USB state stores to avoid racesKeith Packard2012-06-27
* altos: include targe SPI speed in get requestKeith Packard2012-06-27
* altos: Wait for i2c START condition before setting interrupt bitsKeith Packard2012-06-27
* altos: stm i2c debug code was calling flush() even when disabledKeith Packard2012-06-27
* altos: mpu6000 requires a delay during startKeith Packard2012-06-27
* altos: Create a 32-bit 1MHz timer for use in profiling executionKeith Packard2012-06-26
* altos: Optimize FEC encode and decodeKeith Packard2012-06-26
* altos: Clean up usage of port parametersKeith Packard2012-06-26
* altos: Get cc1120 packet reception workingKeith Packard2012-06-25
* altos: Crank down STM SPI speed for MMKeith Packard2012-06-21
* altos: Add full MM telemetryKeith Packard2012-06-21
* altos: Configure STM LCD driver for giant LCD digitsKeith Packard2012-06-21
* altos: hack STM serial number to 58Keith Packard2012-06-17
* altos: Be more careful about register save/restore in ao_yieldKeith Packard2012-06-17
* altos: Reduce STM SPI data rate to 4MHzKeith Packard2012-06-15
* altos: Intgrate hmc5883 sensor into adc ringKeith Packard2012-06-02
* altos: Reset i2c controller at boot timeKeith Packard2012-06-02
* altos: Fix broken EXTI edge mode selections. Clear pending exti on enableKeith Packard2012-06-02
* altos: Route correct GPIO line to interrupt controllerKeith Packard2012-06-02
* altos: Add support for MegaAccel daughter card.Keith Packard2012-06-01
* altos: Timers clock base depends on perhipheral bus prescalers tooKeith Packard2012-06-01
* altos: Clear stm i2c transfer timeout alarmKeith Packard2012-05-28
* altos: Make telemetrum-v1.1 compile with new ao_data structureKeith Packard2012-05-27
* altos: Don't start ADC ring until the other sensors have a valid valueKeith Packard2012-05-27
* altos: Data packet tick count does not live in adc structureKeith Packard2012-05-27
* Get megametrum ready to at least log flight dataKeith Packard2012-05-25
* altos: stm: pass DMA buffer index to DMA completion callbackKeith Packard2012-05-07
* altos: stm: delay during USB config with pull-up offKeith Packard2012-05-07
* altos: stm: share i2c_stop code between send and recvKeith Packard2012-05-07
* altos: stm i2c DMA for large recv appears to workKeith Packard2012-05-06
generated by cgit v1.2.3 (git 2.39.1) at 2025-12-27 06:53:02 +0000