1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
166
167
168
169
170
171
172
173
174
175
176
177
178
179
180
181
182
183
184
185
186
187
188
189
190
191
192
193
194
195
196
197
198
199
200
201
202
203
204
205
206
207
208
209
210
211
212
213
214
215
216
217
218
219
220
221
222
223
224
225
226
227
228
229
230
231
232
233
234
235
236
237
238
239
240
241
242
243
244
245
|
ifdef::altusmetrum[]
==== Main Deploy Altitude
This sets the altitude (above the recorded pad
altitude) at which the 'main' igniter will fire. The
drop-down menu shows some common values, but you can
edit the text directly and choose whatever you
like. If the apogee charge fires below this altitude,
then the main charge will fire two seconds after the
apogee charge fires.
==== Apogee Delay
When flying redundant electronics, it's often
important to ensure that multiple apogee charges don't
fire at precisely the same time, as that can over
pressurize the apogee deployment bay and cause a
structural failure of the air-frame. The Apogee Delay
parameter tells the flight computer to fire the apogee
charge a certain number of seconds after apogee has
been detected.
==== Apogee Lockout
Apogee lockout is the number of seconds after boost
where the flight computer will not fire the apogee
charge, even if the rocket appears to be at
apogee. This is often called 'Mach Delay', as it is
intended to prevent a flight computer from
unintentionally firing apogee charges due to the
pressure spike that occurrs across a mach
transition. Altus Metrum flight computers include a
Kalman filter which is not fooled by this sharp
pressure increase, and so this setting should be left
at the default value of zero to disable it.
endif::altusmetrum[]
ifdef::radio[]
==== Frequency
This configures which of the frequencies to use for
both telemetry and packet command mode. Note that if
you set this value via packet command mode, the
TeleDongle frequency will also be automatically
reconfigured to match so that communication will
continue afterwards.
==== RF Calibration
The radios in every Altus Metrum device are calibrated
at the factory to ensure that they transmit and
receive on the specified frequency. If you need to
you can adjust the calibration by changing this value.
Do not do this without understanding what the value
means, read the appendix on calibration and/or the
source code for more information. To change a
TeleDongle's calibration, you must reprogram the unit
completely.
==== Telemetry/RDF/APRS Enable
Enables the radio for transmission during
flight. When disabled, the radio will not
transmit anything during flight at all.
==== Telemetry baud rate
This sets the modulation bit rate for data
transmission for both telemetry and packet
link mode. Lower bit rates will increase range
while reducing the amount of data that can be
sent and increasing battery consumption. All
telemetry is done using a rate 1/2 constraint
4 convolution code, so the actual data
transmission rate is 1/2 of the modulation bit
rate specified here.
==== APRS Interval
How often to transmit GPS information via APRS
(in seconds). When set to zero, APRS
transmission is disabled.
ifdef::altusmetrum[]
This option is
available on TeleMetrum v2 and TeleMega
boards. TeleMetrum v1 boards cannot transmit
APRS packets.
endif::altusmetrum[]
Note that a single APRS packet
takes nearly a full second to transmit, so
enabling this option will prevent sending any
other telemetry during that time.
==== APRS SSID
Which SSID to report in APRS packets. By
default, this is set to the last digit of the
serial number, but can be configured to any
value from 0 to 9.
==== APRS Format
Whether to send APRS data in Compressed or
Uncompressed format. Compressed format is
smaller and more precise. Uncompressed
format is older, but may work better with your
device. The Kenwood TH-D72 only displays
altitude information with Uncompressed
format, while the Yaesu FT1D only displays
altitude with Compressed format. Test before
you fly to see which to use.
==== Callsign
This sets the call sign included in each
telemetry packet. Set this as needed to
conform to your local radio regulations.
endif::radio[]
ifdef::altusmetrum[]
==== Maximum Flight Log Size
This sets the space (in kilobytes) allocated
for each flight log. The available space will
be divided into chunks of this size. A smaller
value will allow more flights to be stored, a
larger value will record data from longer
flights.
==== Ignitor Firing Mode
This configuration parameter allows the two standard ignitor
channels (Apogee and Main) to be used in different
configurations.
Dual Deploy::
This is the usual mode of operation; the
'apogee' channel is fired at apogee and the
'main' channel at the height above ground
specified by the 'Main Deploy Altitude' during
descent.
Redundant Apogee::
This fires both channels at apogee, the
'apogee' channel first followed after a two
second delay by the 'main' channel.
Redundant Main::
This fires both channels at the height above
ground specified by the Main Deploy Altitude
setting during descent. The 'apogee' channel
is fired first, followed after a two second
delay by the 'main' channel.
ifdef::telemetrum,telemega,easymega[]
==== Pad Orientation
Because they include accelerometers,
TeleMetrum, TeleMega and EasyMega are
sensitive to the orientation of the board. By
default, they expect the antenna end to point
forward. This parameter allows that default to
be changed, permitting the board to be mounted
with the antenna pointing aft instead.
Antenna Up::
In this mode, the antenna end of the flight
computer must point forward, in line with the
expected flight path.
Antenna Down::
In this mode, the antenna end of the flight
computer must point aft, in line with the
expected flight path.
endif::telemetrum,telemega,easymega[]
==== Beeper Frequency
The beeper on all Altus Metrum flight
computers works best at 4000Hz, however if you
have more than one flight computer in a single
airframe, having all of them sound at the same
frequency can be confusing. This parameter
lets you adjust the base beeper frequency
value.
endif::altusmetrum[]
ifdef::telegps[]
==== Logging Trigger Motion
This sets the amount of motion that TeleGPS
needs to see before logging the new
position. Motions smaller than this are
skipped, which saves storage space.
==== Position Reporting Interval
The interval between TeleGPS position reports,
both over the air and in the log. Increase
this to reduce the frequency of radio
transmissions and the length of time available
in the log.
endif::telegps[]
ifdef::telemega,easymega[]
==== Configure Pyro Channels
.Additional Pyro Channel Configuration
image::configure-pyro.png[width="5.5in"]
This opens a separate window to configure the
additional pyro channels available on TeleMega
and EasyMega. One column is presented for
each channel. Each row represents a single
parameter, if enabled the parameter must meet
the specified test for the pyro channel to be
fired.
Select conditions and set the related value;
the pyro channel will be activated when *all*
of the conditions are met. Each pyro channel
has a separate set of configuration values, so
you can use different values for the same
condition with different channels.
At the bottom of the window, the 'Pyro Firing
Time' configuration sets the length of time
(in seconds) which each of these pyro channels
will fire for.
Once you have selected the appropriate
configuration for all of the necessary pyro
channels, you can save the pyro configuration
along with the rest of the flight computer
configuration by pressing the 'Save' button in
the main Configure Flight Computer window.
include::pyro-channels.raw[]
endif::telemega,easymega[]
|
