summaryrefslogtreecommitdiff
path: root/src
Commit message (Collapse)AuthorAge
* altos: Use simpler debounce logic for buttonstelelaunchtwoKeith Packard2015-12-25
| | | | | | | | | | | Instead of waiting for a while after the transition to decide if it has stuck, signal the event right away and then ignore other transitions for the debounce interval. This seems to work just as reliably, but has the benefit of eliminating button latency at press time. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add ao_lco_two.c; alternate LCO interface codeKeith Packard2015-12-25
| | | | | | | | The LCO interface is likely to end up very device specific as the interactions depends on the input devices. Here's a version for TeleLCOTwo, which has two arming switches and a firing button. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add easy mini plotting helper in test codeKeith Packard2015-12-23
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fix telefiretwo .gitignoreKeith Packard2015-12-23
| | | | | | Was ignoring the wrong built files Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add TeleLCOTwo firmwareKeith Packard2015-12-23
| | | | | | The LCO side of a two-channel launch controller setup. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Support pad/lco boxes with fixed box numbersKeith Packard2015-12-23
| | | | | | | This allows for a configuration without adjustable box numbers on either end of the link, simplifying the UI. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Allow for pad boxes with different sensor configurationsKeith Packard2015-12-23
| | | | | | | | This allows for a pad box without a resistor from power to each FET. That resistor is needed to detect welded relays, but in a solid-state system, that's not a possibility. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: telefiretwo-v0.1 bitsKeith Packard2015-12-23
| | | | | | Get this board running. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add pad support for new telefire versionsKeith Packard2015-12-23
| | | | | | | | | | | | Makes the voltage divider values configurable, and allows for pyro channels that don't have the resistors necessary to check for a stuck relay. Also supports STM32L processors with wider GPIO registers, and uses the new ao_gpio_set/clr_bits functions to fire igniters rather than cc1111-specific code. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Support telefire products in cc1200 driverKeith Packard2015-12-23
| | | | | | Need to disable the pad code while testing the radio. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add ao_gpi_set/clr_bits functionsKeith Packard2015-12-23
| | | | | | These set or clear a group of bits in a single GPIO register all together. Signed-off-by: Keith Packard <keithp@keithp.com>
* telelco: Fix pad reset to one on radio signal lossKeith Packard2015-10-13
| | | | | | | The pad number was getting reset back to one when signal was lost, causing pad one to get fired in this case even when already set to arm mode. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/telelco: Adjust drag race UIKeith Packard2015-10-13
| | | | | | | | | Enter/leave drag race is done by rotating the box selector knob to a new 'dr' position and then holding down the firing button; this avoids a potential accidental firing if you somehow don't realize you've armed the box before selecting drag race mode. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/telelco: Add drag race UIKeith Packard2015-08-29
| | | | | | | | | | | | | | | | | | | | | | | | | | | | With the unit disarmed, press and hold the fire button for five seconds to enable drag race mode. The display will show 'dr' for five seconds and beep five times to indicate that drag race mode is enabled. The decimal points in the display will all be displayed as an additional visual aid. Once every five seconds, it will beep. With drag race mode enabled, you can select a box/pad pair and press the 'fire' button to add it to the drag race group. For the current box, all members of the drag race group will have their continuity LEDs blink slowly. There will be no indication of continuity in this mode; you'll want to check that before enabling drag race mode. If you want to de-select a member of the group, just press the fire button again. Each time you push the fire button, it will beep out the pad number added or removed. Arm the box and you will not be able to add or remove members from the drag race group. Firing will simultaneously fire all members of the drag race group. To disable drag race mode, press and hold the fire button for two seconds. It will beep twice and turn off the decimal points in the display. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/telelco: Infrastructure changes for drag racingKeith Packard2015-08-29
| | | | | | | This makes the lco management code support arming multiple pads and firing all of them at once. The UI code does not expose this yet. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Provide direct segment driving interface for LCD displaysKeith Packard2015-08-29
| | | | | | | This exposes a simple bit-mask for setting the seven segments instead of just allowing hex-decimal values. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/telefire: No reply for ARMED. Ignore time for FIRE.Keith Packard2015-08-29
| | | | | | | This will let us do drag races by letting the LCO arm multiple boxes and fire them all with a single command. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add HAS_COMPANION to new boards with companion connectorsKeith Packard2015-08-20
| | | | | | | | | | | Thanks much to Rob Derstadt for discovering this bug! TeleMetrum v2.0, TeleMega, EasyMega, TeleBalloon v2.0 all have companion connectors and yet HAS_COMPANION was not defined. This disabled companion telemetry packets on these products, but otherwise didn't have any effect. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/telebt-v3.0: Report battery voltage correctlyKeith Packard2015-06-25
| | | | | | | There was an extra %d, and an extra ':' in the output, making the UI not parse the voltage correctly Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/telelco: Show box voltage with pad knob instead of firing buttonKeith Packard2015-05-25
| | | | | | | | Turn left past '1' and see the firing box battery voltage instead of pushing the firing button with the box disarmed. This seems like a safer UI. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/telelco: Display telefire battery voltageKeith Packard2015-05-25
| | | | | | | When the firing button is pressed while unarmed, show the telefire battery voltage in the display. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add telelco v0.3 (v0.2 with cc1200 instead of cc1120)Keith Packard2015-05-25
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* telefire: Report telefire battery voltage over telemetry linkKeith Packard2015-05-25
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Only set CMAC RSSI value on valid packet receivedKeith Packard2015-05-24
| | | | | | | | This ignores spurious packets for the purpose of showing the RSSI value in telelco/telefire, avoiding warning about 'low RSSI' when the radio receives noise. Signed-off-by: Keith Packard <keithp@keithp.com>
* telefire: Make 'good' RSSI value configurableKeith Packard2015-05-24
| | | | | | | | Different radios will have different 'good' RSSI values, so let each product configure it, leaving the default set to -90dBm, which is a solid signal value for the CC1111. Signed-off-by: Keith Packard <keithp@keithp.com>
* micropeak: Use fast load mode by default in -load scriptKeith Packard2015-05-19
| | | | | | Speed up flashing in default config Signed-off-by: Keith Packard <keithp@keithp.com>
* microsplash: Add 'publish' target to MakefileKeith Packard2015-05-19
| | | | | | | This dumps the resulting binary and -load script into the Binaries directory of the altusmetrumllc repo Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Support 32MHz xtal on cc1200Keith Packard2015-05-19
| | | | | | | I ended up building some cc1200-based boards with 32MHz xtals, so just make this an option when building the driver. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stmf0: Have fast ADC ring buffer code use wrap-aroundKeith Packard2015-03-20
| | | | | | | | | Instead of requiring that the whole set of returned values fit precisely in the ring, allow for wrap-around so that we can fetch an odd number of ADC values. The previous version required that the fetch amount always be a factor of the ADC buffer size. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/chaoskey: Set USB VID/PID to 0x1d50/0x60c6Keith Packard2015-03-19
| | | | | | | These are allocated from the OpenMoko USB vendor ID page and offer a more 'official' number than from using the 0xfffe space. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add the ability to configure a different USB vendor IDKeith Packard2015-03-19
| | | | | | | ChaosKey will use an OpenMoko vid/pid, so we need the ability to configure a different USB vendor ID for each product. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/test: Support old telemega eeprom file formats in ao_flight_testKeith Packard2015-03-10
| | | | | | | | The old eeprom format used different stoarge for the accel calibration data, which doesn't matter to this code, but the change in the format value does. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/test: Make aprs test code compile againKeith Packard2015-03-10
| | | | | | Adding the compressed/uncompressed config option broke the APRS test harness. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stmf0: Need ao_exti.h for pin configurationKeith Packard2015-03-07
| | | | | | Flash loader uses pin configuration to set up GPIOs for boot selection Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add makefile for chaoskey flash loaderKeith Packard2015-03-07
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Build chaoskey by defaultKeith Packard2015-03-07
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add .gitignore for chaoskeyKeith Packard2015-03-07
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Missing pad field in TMv2 data packetKeith Packard2015-03-02
| | | | | | | | | | The normal ARM padding would have filled this in correctly, but it's best to be explicit about the structure. This also adds a test to make sure the resulting telemetry declaration is exactly 32 bytes, Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Wait for BT disconnect before sending commandKeith Packard2015-03-02
| | | | | | | | | | | If AltosDroid manages to connect to the BT module before we've configured it, we won't be able to talk to it as we can't force the module to ignore connection attempts. Wait for AltosDroid to give up and let us configure the device. Eventually, we'll manage, if AltosDroid's delay interval is longer than the time it takes to configure the unit. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make APRS format (compressed/uncompressed) configurableKeith Packard2015-03-02
| | | | | | | | This provides a choice of compressed vs uncompressed when sending APRS packets to deal with receivers that still do not have support for the more useful compressed format. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/usbtrng: Split out random number generating code to separate driverKeith Packard2015-02-28
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add chaoskey flash loaderKeith Packard2015-02-28
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Create chaoskey productKeith Packard2015-02-28
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stmf0: Allocate USB buffers at startupKeith Packard2015-02-28
| | | | | | | This lets the extra allocations used from ao_usb_alloc_buffers be allocated before the first USB connection happens. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stmf0: Typo in ao_crc_stm.cKeith Packard2015-02-28
| | | | | | Extra semicolon Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stmf0: Fix fast ADC interfaceKeith Packard2015-02-28
| | | | | | | This was configuring the hardware wrong, and wasn't keeping the output ring full. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Allow software to offer other USB interface classes than CDCKeith Packard2015-02-28
| | | | | | | This lets some boards offer non-CDC class USB interfaces so that the modem driver doesn't pick them up. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove some accidental debug printfs from ao_packet.cKeith Packard2015-02-15
| | | | | | | While fixing the cc1200 configuration, I added some debug printfs to this code. They were accidentally committed with the fix... Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/cc1200: Adjust bit-sync configurationKeith Packard2015-02-14
| | | | | | | | | | | | | The default bit timing adjustment mechanism allows for only a 0.2% deviation from the programmed bit timing. I found one TeleMini device which is beyond that tolerance as it was built with an older crystal with more error. Switch to the more expensive synchronization mechanism which allows up to 2% timing error, but requires a multi-byte preamble (which we have). This fixes packet mode nicely. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: embed ao_alarm and ao_clear_alarm in ao_sleep_forKeith Packard2015-02-14
| | | | | | | sdcc won't embed these itself, and thus consumes too much flash for telemetrum-v1.0 Signed-off-by: Keith Packard <keithp@keithp.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-10-18 16:36:34 +0000