summaryrefslogtreecommitdiff
path: root/src
Commit message (Collapse)AuthorAge
...
* altos: ao_storage_read already calls ao_storage_setupKeith Packard2012-06-17
| | | | | | No need to call twice. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Use interrupts to wake up after RDF transmission.Keith Packard2012-06-17
| | | | | | Also clean up the debug output Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Crank cc1120 power down to 0dBm to avoid crashing CPUKeith Packard2012-06-17
| | | | | | | Looks like RFI from the transmitter is confusing the CPU; lower the 1120 power output from +14dBm to +0dBm to keep the CPU happy. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Reduce STM SPI data rate to 4MHzKeith Packard2012-06-15
| | | | | | cc1120 doesn't want more than 6.1MHz, otherwise it gets very angry. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Start making cc1120 radio workKeith Packard2012-06-15
| | | | | | RDF tones and radio calibration work now. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fix cc1120 packet mode datarate and configKeith Packard2012-06-15
| | | | | | Was using the wrong function Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make sure cc1120 is initialized correctly at startup timeKeith Packard2012-06-15
| | | | | | Check to make sure it pulls down MISO when CS is enabled. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: use 'b' command for radio beepKeith Packard2012-06-15
| | | | | | 'B' is used by the baro data dumper. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fix RDF mode data rate and PKT_CFG0 valueKeith Packard2012-06-15
| | | | | | | Changes tone to the desired 1kHz frequency and ensures the PKT_CFG0 has the right value. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Actually write cc1120 register valuesKeith Packard2012-06-15
| | | | | | Helps to not use 'read' mode when writing. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Configure cc1120 frequencyKeith Packard2012-06-15
| | | | | | | Set default conversion value, and pull the selected frequency calibration data out of the config block. Signed-off-by: Keith Packard <keithp@keithp.com>
* Temporarily disable packet and telem on MMKeith Packard2012-06-15
| | | | | | While work on the radio code progresses Signed-off-by: Keith Packard <keithp@keithp.com>
* Allow product to override maximum number of command lists (NUM_CMDS)Keith Packard2012-06-15
| | | | | | Just in case some product wants to save memory, or have more. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make cc1111 products all depend on ao_arch.h and ao_arch_func.hKeith Packard2012-06-04
| | | | | | Ensures that files get recompiled as needed Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Other half of the ms5607 prom reporting patchKeith Packard2012-06-04
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: typo in ao_monitor prevented ground station from including codeKeith Packard2012-06-04
| | | | | | | This created ground station software that couldn't actually receive and report telemetry packets. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make 'v' command dump pressure sensor ROM valuesKeith Packard2012-06-04
| | | | | | Avoids needing a new command Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: fix test builds of non-accel flight codeKeith Packard2012-06-04
| | | | | | | Remove references to accel variables when building baro-only flight test code. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Legacy telemetry needs original ADC recordKeith Packard2012-06-04
| | | | | | | | The legacy telemetry packets included the raw ADC structure directly, so make sure that doesn't change further, allowing teledongle firmware to remain compatible with old TM firmware. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove unused AES code from teledongle and tidongleKeith Packard2012-06-04
| | | | | | Leave this out as neither of these products need it. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove accel_ref from pre v1.1 TM firmwareKeith Packard2012-06-04
| | | | | | | V1.0 needs RAM space for flash buffer, leaving too little room for this extra data. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Intgrate hmc5883 sensor into adc ringKeith Packard2012-06-02
| | | | | | | Creates a task to poll the mag sensor and place the data into the sensor data ring. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Get HMC5883 driver limping alongKeith Packard2012-06-02
| | | | | | Not pushing data into the ring yet, but the chip appears to work now. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Reset i2c controller at boot timeKeith Packard2012-06-02
| | | | | | In case it's wedged. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fix broken EXTI edge mode selections. Clear pending exti on enableKeith Packard2012-06-02
| | | | | | | | | Make sure the edge mode registers are set according to the requested mode. Clear any pending interrupt when enabling to avoid spurious isr call Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Route correct GPIO line to interrupt controllerKeith Packard2012-06-02
| | | | | | | Which GPIO a particular pin interrupt comes from is selected by the SYSCFG EXTICR registers; set these when an exti interrupt is configured. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Enable some debugging during flight mode on MMKeith Packard2012-06-02
| | | | | | | | Until we've got the radio working, there's no way to see inside the MM state without using USB. Add a diagnostic command to dump out the internal flight state variables. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add support for MegaAccel daughter card.Keith Packard2012-06-01
| | | | | | | | | Switches all acceleration computation to using the MegaAccel accelerometer to ensure support for high-g flights. MPU6000 values continue to be logged as normal Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Timers clock base depends on perhipheral bus prescalers tooKeith Packard2012-06-01
| | | | | | | | For some weird reason, a non-unity perhipheral bus clock scaler affects the base of the various timers; this left the 100Hz tick running at 200Hz. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: megametrum has loggingKeith Packard2012-06-01
| | | | | | | This makes sure the various other subsystems know about it, like the 'v' command. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: add high-z accel and mag sensor to megametrum loggingKeith Packard2012-06-01
| | | | | | These nicely fill the 32-byte sensor log record Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Mark full and mega logging correctly in 'v' commandKeith Packard2012-06-01
| | | | | | Make sure megametrum reports 'log format 5'. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Clear stm i2c transfer timeout alarmKeith Packard2012-05-28
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove debug printf from accel auto-calKeith Packard2012-05-28
| | | | | | Otherwise, this goes way too slow Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Clean up ADC selection for cc1111Keith Packard2012-05-28
| | | | | | Depend directly on product defines instead of trying to guess Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: All cc1111 products have a radioKeith Packard2012-05-28
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Shrink telemetry generation codeKeith Packard2012-05-28
| | | | | | otherwise TM doesn't build anymore Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Try to get hmc5883 workingKeith Packard2012-05-28
| | | | | | No joy yet Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make teleterra v0.2 compile with new ao_data structKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make telepyro-v0.1 build with new ao_data structKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make telescience-v0.1 build with new ao_data structKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make telenano build with new ao_data structureKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make stm-demo compile with new ao_data structureKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make telemini-v1.0 compile with new ao_data structureKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make telemetrum-v1.0 build with new ao_data structureKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make telemetrum-v1.1 compile with new ao_data structureKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* ignore pa to altitude conversion fileKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Split out mm-specific versions of sampling codeKeith Packard2012-05-27
| | | | | | Avoid breaking telemetrum (too much) by splitting this stuff apart. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Don't start ADC ring until the other sensors have a valid valueKeith Packard2012-05-27
| | | | | | Yes, this is still an ugly kludge, but it's easy. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Data packet tick count does not live in adc structureKeith Packard2012-05-27
| | | | | | It was moved to the global structure. Having two is confusing. Signed-off-by: Keith Packard <keithp@keithp.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-10-18 21:38:23 +0000