summaryrefslogtreecommitdiff
path: root/src
Commit message (Collapse)AuthorAge
* Add --cal to man pageKeith Packard2009-12-15
|
* Allow radio calibration to be set from ao-loadKeith Packard2009-12-05
| | | | | | | | This moves the initial radio calibration value into const memory where it will be used if no eeprom configuration value is available, either on an unprogrammed board with eeprom or a device without an eeprom. Signed-off-by: Keith Packard <keithp@keithp.com>
* Re-order config values. Change frequency to calKeith Packard2009-12-05
| | | | | | | Place more often used values at top, and consistently call the radio value 'calibration' instead of 'frequency'. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add radio calibration configuration.Keith Packard2009-12-04
| | | | | | | | | The crystal we use is only good for 20ppm, which generates a fairly significant error bounds at our RF frequency. This commit adds a configuration variable that sets the RF frequency control variable so that the output frequency can be adjusted. Signed-off-by: Keith Packard <keithp@keithp.com>
* Make ao_cmd_decimal produce both 32 and 16 bit values.Keith Packard2009-12-04
| | | | | | | ao_cmd_lex_u32 is produced in addition to ao_cmd_lex_i so that functions can easily read 32-bit values from the command line. Signed-off-by: Keith Packard <keithp@keithp.com>
* Remove send_serial and serial_baud commands.Keith Packard2009-12-04
| | | | | | No longer useful, and they take up space. Signed-off-by: Keith Packard <keithp@keithp.com>
* Change default callsign to "N0CALL"Keith Packard2009-12-04
|
* Make TD print 0000-00-00 for invalid dates.Keith Packard2009-11-21
| | | | | | This 'shouldn't' happen, but in case it does, I want to know about it. Signed-off-by: Keith Packard <keithp@keithp.com>
* Decode HDOP data from skytraq GPSKeith Packard2009-11-21
| | | | | | | | The hdop data was getting dropped on the floor, but is rather useful when deciding if the GPS position is crazy or not. This reports HDOP * 5 (giving a useful range of .2-50). Signed-off-by: Keith Packard <keithp@keithp.com>
* Reduce igniter firing time from 500ms to 50ms.Keith Packard2009-11-20
| | | | | | | Given that the system will brown-out with the longer pulse, it doesn't make sense to even try; failure at 50ms probably indicates a short. Signed-off-by: Keith Packard <keithp@keithp.com>
* fix typo in commentBdale Garbee2009-11-20
|
* Stop using SiRF state info.Keith Packard2009-11-15
| | | | | | | | With the switch to the skytraq GPS unit, we don't have the same level of detail in the GPS stream, so stop reporting that in the telemetry stream, in the UI and writing it to eeprom. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add date to GPS data, captured from GPRMC packet.Keith Packard2009-11-15
| | | | | | | Pull the date out of the GPS stream and send it over the telemetry link and write it to the eeprom. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add flight number to telemetry stream.Keith Packard2009-11-15
| | | | | | | | This makes it easier to tie the telemetry and eeprom files together as they're now both labeled with serial and flight numbers, which should be unique. Signed-off-by: Keith Packard <keithp@keithp.com>
* Provide a dummy 'uninstall' target in the src directory.Keith Packard2009-11-14
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* Loosen tolerances for main->landed transitionKeith Packard2009-11-14
| | | | | | | | | | | | | | | Detecting that the rocket has landed is required for the system to flush the eeprom log and re-enable the RDF beacon. This patch changes the landed state entry requirements for the accelerometer to require only that the accelerometer stay within a quarter of a g (down from 1/10g) and changes the testing interval from 20 seconds to 5 seconds. The requirement that the barometric altitude be within 1000m of the launch altitude and that the barometer change by no more than 0.05kPa are unchanged. Signed-off-by: Keith Packard <keithp@keithp.com>
* Return radio to telemetry settings when packet system closed.Keith Packard2009-11-05
| | | | | | | To receive telemetry after disabling the packet system, the radio must be reconfigured for telemetry mode. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add reboot command.Keith Packard2009-11-05
| | | | | | This resets the processor using the watchdog timer. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add Watchdog Timer Control register definitionsKeith Packard2009-11-05
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* Move ao_match_word from ao_ignite.c to ao_cmd.cKeith Packard2009-11-05
| | | | | | This is a generally useful command line utility. Signed-off-by: Keith Packard <keithp@keithp.com>
* Explicitly use USB I/O routines in packet codeKeith Packard2009-11-04
| | | | | | | | | Using the implicit stdio functions (putchar/getchar/flush) would result in essentially random redirection of each, depending on whether the packet code had characters available when getchar was called. This would cause lockups in putchar. Signed-off-by: Keith Packard <keithp@keithp.com>
* In USB pollchar, wait for packet before re-checking USB out lenKeith Packard2009-11-04
| | | | | | | | | This probably wouldn't actually cause a problem, but it seems more reliable to wait for a packet interrupt before re-reading the packet OUT len register. This could avoid spinning while waiting for a USB packet, which seems like a good thing. Signed-off-by: Keith Packard <keithp@keithp.com>
* In packet master, move USB flush from packet thread to echo threadKeith Packard2009-11-04
| | | | | | | | This keeps the packet thread from blocking on USB and also makes the flush happen after every packet (slightly more USB traffic, but packets are slow anyway). Signed-off-by: Keith Packard <keithp@keithp.com>
* Pass accel calibration over telemetry stream. Telemetry data format change.Keith Packard2009-11-03
| | | | | | | | | | | This allows the ground station to convert the accelerometer sensor values into acceleration and speed data. This requires a new telemetry data structure, and so TeleMetrum and TeleDongle units must be updated synchronously. ao-view will parse either telemetry stream, and the serial format from TeleDongle now has a version number to allow for future changes. Signed-off-by: Keith Packard <keithp@keithp.com>
* ao_flight_test was using accel value for pressure tooKeith Packard2009-11-02
|
* Reformat ADC values to show all 16 bitsKeith Packard2009-11-02
|
* Remove "f" commandKeith Packard2009-11-02
|
* Remove "d" commandKeith Packard2009-11-02
|
* Remove "l" command as ao-dumplong no longer uses itKeith Packard2009-11-02
|
* Add two-point accelerometer calibration.Keith Packard2009-11-02
| | | | | | | Calibration now uses two values, one upside right and the other upside down instead of a single horizontal value. This allows the use of other accelerometers and compensates for variations in the divider circuit to provide more accurate data.
* Add ao_usb_pollchar to ao.hKeith Packard2009-11-02
|
* Disable interrupts while removing tasks from task listKeith Packard2009-11-02
|
* Enable packet-based communcation to command processorKeith Packard2009-11-01
| | | | | | | This splits the packet code into master/slave halves and hooks the slave side up to the getchar/putchar/flush logic in ao_stdio.c Signed-off-by: Keith Packard <keithp@keithp.com>
* No need to wakeup &ao_tick_count nowKeith Packard2009-10-31
|
* Poke master to speed up packet rate when things are busyKeith Packard2009-10-31
|
* Use ao_alarm for ao_delay so it can be easily interruptedKeith Packard2009-10-31
|
* Do more flushing in packet test codeKeith Packard2009-10-30
|
* Add RFIM registerKeith Packard2009-10-30
|
* Send SYN packet to set sequence numbersKeith Packard2009-10-30
|
* Use ao_radio_done to wait for TX to completely finish with packetKeith Packard2009-10-30
|
* Switch packet code from timer thread to ao_alarmKeith Packard2009-10-30
|
* Remove reason from ao_dma_abortKeith Packard2009-10-30
|
* Add ao_alarmKeith Packard2009-10-30
|
* Wait for TX to finish sending dataKeith Packard2009-10-30
|
* Add radio carrier commandKeith Packard2009-10-30
|
* Initial packet bits. Just testing transmissionKeith Packard2009-10-30
|
* Add ao_wake_task and ao_exitKeith Packard2009-10-16
| | | | | | | ao_wake_task signals a specific task to wake up. ao_exit terminates the current task. Signed-off-by: Keith Packard <keithp@keithp.com>
* Save some DSEG space by marking cmd functions __reentrantKeith Packard2009-10-16
| | | | | | | __reentrant causes the compiler to place args and locals on the stack instead of in the data segment. Signed-off-by: Keith Packard <keithp@keithp.com>
* Merge branch 'master' into skytraqKeith Packard2009-10-10
|\
| * Add apogee igniter delay.Keith Packard2009-10-10
| | | | | | | | | | | | | | Provide for a delay after apogee before the drogue charge is fired. This allows TM to be used as a back-up altimeter. Signed-off-by: Keith Packard <keithp@keithp.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-10-15 23:36:27 +0000