summaryrefslogtreecommitdiff
path: root/src
Commit message (Collapse)AuthorAge
...
* altos: hack STM serial number to 58Keith Packard2012-06-17
| | | | | | otherwise altosui won't record telemetry Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: make cc1120 ao_radio_send re-entrantKeith Packard2012-06-17
| | | | | | It gets called from multiple tasks, so put local data on the stack. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add telemetry to megametrumKeith Packard2012-06-17
| | | | | | Now that the radio works Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Software implemenation of CC1111 radio encodingKeith Packard2012-06-17
| | | | | | | Add CRC, whitening, FEC and interleaving routines for transmission path to allow cc1120 to send telem packets to cc1111. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Be more careful about register save/restore in ao_yieldKeith Packard2012-06-17
| | | | | | | Make sure the general registers are all saved before messing with any of them. Then, explicitly use r0 to save/restore apsr and primask. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Don't lose IRQ disabled state in ao_sleepKeith Packard2012-06-17
| | | | | | | | | | | | Using ao_arch_critical around the wchan setting will force interrupts to be re-enabled before ao_yield records the state of that bit, potentially causing problems with functions not atomically testing and sleeping. Tasks that need to set wchan with interrupts disabled should have interrupts disabled when entering ao_sleep already. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: ao_storage_read already calls ao_storage_setupKeith Packard2012-06-17
| | | | | | No need to call twice. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Use interrupts to wake up after RDF transmission.Keith Packard2012-06-17
| | | | | | Also clean up the debug output Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Crank cc1120 power down to 0dBm to avoid crashing CPUKeith Packard2012-06-17
| | | | | | | Looks like RFI from the transmitter is confusing the CPU; lower the 1120 power output from +14dBm to +0dBm to keep the CPU happy. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Reduce STM SPI data rate to 4MHzKeith Packard2012-06-15
| | | | | | cc1120 doesn't want more than 6.1MHz, otherwise it gets very angry. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Start making cc1120 radio workKeith Packard2012-06-15
| | | | | | RDF tones and radio calibration work now. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fix cc1120 packet mode datarate and configKeith Packard2012-06-15
| | | | | | Was using the wrong function Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make sure cc1120 is initialized correctly at startup timeKeith Packard2012-06-15
| | | | | | Check to make sure it pulls down MISO when CS is enabled. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: use 'b' command for radio beepKeith Packard2012-06-15
| | | | | | 'B' is used by the baro data dumper. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fix RDF mode data rate and PKT_CFG0 valueKeith Packard2012-06-15
| | | | | | | Changes tone to the desired 1kHz frequency and ensures the PKT_CFG0 has the right value. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Actually write cc1120 register valuesKeith Packard2012-06-15
| | | | | | Helps to not use 'read' mode when writing. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Configure cc1120 frequencyKeith Packard2012-06-15
| | | | | | | Set default conversion value, and pull the selected frequency calibration data out of the config block. Signed-off-by: Keith Packard <keithp@keithp.com>
* Temporarily disable packet and telem on MMKeith Packard2012-06-15
| | | | | | While work on the radio code progresses Signed-off-by: Keith Packard <keithp@keithp.com>
* Allow product to override maximum number of command lists (NUM_CMDS)Keith Packard2012-06-15
| | | | | | Just in case some product wants to save memory, or have more. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make cc1111 products all depend on ao_arch.h and ao_arch_func.hKeith Packard2012-06-04
| | | | | | Ensures that files get recompiled as needed Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Other half of the ms5607 prom reporting patchKeith Packard2012-06-04
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: typo in ao_monitor prevented ground station from including codeKeith Packard2012-06-04
| | | | | | | This created ground station software that couldn't actually receive and report telemetry packets. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make 'v' command dump pressure sensor ROM valuesKeith Packard2012-06-04
| | | | | | Avoids needing a new command Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: fix test builds of non-accel flight codeKeith Packard2012-06-04
| | | | | | | Remove references to accel variables when building baro-only flight test code. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Legacy telemetry needs original ADC recordKeith Packard2012-06-04
| | | | | | | | The legacy telemetry packets included the raw ADC structure directly, so make sure that doesn't change further, allowing teledongle firmware to remain compatible with old TM firmware. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove unused AES code from teledongle and tidongleKeith Packard2012-06-04
| | | | | | Leave this out as neither of these products need it. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove accel_ref from pre v1.1 TM firmwareKeith Packard2012-06-04
| | | | | | | V1.0 needs RAM space for flash buffer, leaving too little room for this extra data. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Intgrate hmc5883 sensor into adc ringKeith Packard2012-06-02
| | | | | | | Creates a task to poll the mag sensor and place the data into the sensor data ring. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Get HMC5883 driver limping alongKeith Packard2012-06-02
| | | | | | Not pushing data into the ring yet, but the chip appears to work now. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Reset i2c controller at boot timeKeith Packard2012-06-02
| | | | | | In case it's wedged. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fix broken EXTI edge mode selections. Clear pending exti on enableKeith Packard2012-06-02
| | | | | | | | | Make sure the edge mode registers are set according to the requested mode. Clear any pending interrupt when enabling to avoid spurious isr call Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Route correct GPIO line to interrupt controllerKeith Packard2012-06-02
| | | | | | | Which GPIO a particular pin interrupt comes from is selected by the SYSCFG EXTICR registers; set these when an exti interrupt is configured. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Enable some debugging during flight mode on MMKeith Packard2012-06-02
| | | | | | | | Until we've got the radio working, there's no way to see inside the MM state without using USB. Add a diagnostic command to dump out the internal flight state variables. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add support for MegaAccel daughter card.Keith Packard2012-06-01
| | | | | | | | | Switches all acceleration computation to using the MegaAccel accelerometer to ensure support for high-g flights. MPU6000 values continue to be logged as normal Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Timers clock base depends on perhipheral bus prescalers tooKeith Packard2012-06-01
| | | | | | | | For some weird reason, a non-unity perhipheral bus clock scaler affects the base of the various timers; this left the 100Hz tick running at 200Hz. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: megametrum has loggingKeith Packard2012-06-01
| | | | | | | This makes sure the various other subsystems know about it, like the 'v' command. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: add high-z accel and mag sensor to megametrum loggingKeith Packard2012-06-01
| | | | | | These nicely fill the 32-byte sensor log record Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Mark full and mega logging correctly in 'v' commandKeith Packard2012-06-01
| | | | | | Make sure megametrum reports 'log format 5'. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Clear stm i2c transfer timeout alarmKeith Packard2012-05-28
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove debug printf from accel auto-calKeith Packard2012-05-28
| | | | | | Otherwise, this goes way too slow Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Clean up ADC selection for cc1111Keith Packard2012-05-28
| | | | | | Depend directly on product defines instead of trying to guess Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: All cc1111 products have a radioKeith Packard2012-05-28
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Shrink telemetry generation codeKeith Packard2012-05-28
| | | | | | otherwise TM doesn't build anymore Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Try to get hmc5883 workingKeith Packard2012-05-28
| | | | | | No joy yet Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make teleterra v0.2 compile with new ao_data structKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make telepyro-v0.1 build with new ao_data structKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make telescience-v0.1 build with new ao_data structKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make telenano build with new ao_data structureKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make stm-demo compile with new ao_data structureKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make telemini-v1.0 compile with new ao_data structureKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-10-16 17:34:45 +0000