| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
v1.0 boards have noisy accelerometer data caused by interactions
between RF transmission and the accelerometer measurements; this noise
generates a negative bias in the accelerometer readings. The net
effect is that the estimated speed is lower than the actual speed,
causing early an apogee estimate.
By increasing the sigma value for accelerometer data, the kalman
filter 'trusts' the acceleration data less, putting more weight on the
barometer data. This causes the estimated time of apogee to be closer
to the correct value.
This reduces the response to changes in acceleration.
This new value is applied solely to TeleMetrum v1.0 boards. v1.1
boards correct for this error, and hence can use the correct sigma
value for the accelerometer.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
These are significantly smaller than the general pointer versions from
libc on the cc1111.
Signed-off-by: Keith Packard <keithp@keithp.com>
Conflicts:
src/Makefile.proto
src/cc1111/ao_adc.c
src/cc1111/ao_packet_master.c
src/core/ao.h
Fix up the new makefiles
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
| |
Split out sources into separate directories:
core: architecture and product independent bits
cc1111: cc1111-specific code
drivers: architecture independent drivers
product: product-specific sources and Makefile fragments
util: scripts for building stuff
This should have no effect on the built products, but testing is encouraged
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
Need to rebuild ao_flight_test when any of the flight sources change
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| | |
|
| |
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
This automates flight code testing by reporting mis-detected apogee or
main events.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
|
|
|
|
| |
This changes the full telemetry stream to include kalman data instead
of the old ad-hoc flight data. It's compatible in that the packet
sizes are the same so teledongle can receive either and figure out
which it has received.
A few plotting and testing tools are added to make validating the new
code easier.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
| |
This runs a long list of flights (there's a user-specific path
pointing at the flights) and squawks if the baro and dual flight
computers don't match.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| | |
|
| |
|
|
|
|
| |
This builds the flight code in baro-only mode for testing.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
Yes, it would be nice to automate dependency generation here, but I
can't be bothered.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| | |
|
|
|
This creates per-product subdirectories and recompiles everything for
each product, allowing per-product compile-time changes for things
like peripheral pin assignments and attached serial devices.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
