| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
| |
Makes gcc happy
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
| |
This cleans up the build process for all architectures, providing a
common place to specify vpath, cflags and build rules for various
common files.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
And update all users to be explicit about the desired config.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
This was used with the 8051 bit-addressing mode to provide
single-instruction access to GPIO pins.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
This works way better than attempting to use the beeper pin.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
| |
Connect this pin to GND (pin 3) and TeleMini will come up with N0CALL
at 434.550MHz using the original frequency calibration. Helps recover
from accidental mis-configuration.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| | |
|
| |
|
|
|
|
| |
Was GPL2, switch to GPL2+
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
|
| |
Pre-USB telemini v3 designs had a separate firmware load for radio
calibration. Now that we've got enough USB to perform flash/cal/test,
we don't need that other firmware load, so we can remove the remaining
Makefile remnants of the calibration load.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
Now that telemini has USB, use the boot loader to make it easy to
update firmware.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
| |
Removed LEDs. Added USB. Flipped lots of pins around.
This appears to make telemini work.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
The beeper code now wants to know which timer, port and pin are in use.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
These were just hooked up wrong in the software.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
Allow the ground software to know which TeleMini version is in use,
even though they are very similar with only ADC values differing.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
TeleMini v3.0 is nearly working; there are some ADC issues still, and
lots of altosui work left to decode the new telemetry packet.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
| |
Separate radio xtal means we run the processor at 48MHz.
Fix the battery monitoring voltage divider resistor values.
Disable most of the code until we've got the radio working.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
For first prototype, which attempted to use the SoC clock for the radio.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
