summaryrefslogtreecommitdiff
path: root/src/stm
Commit message (Collapse)AuthorAge
* altos/stm: Handle USB reset in STM32L usb driverKeith Packard2016-06-10
| | | | | | | Just like lpc and stmf0, deal with the host resetting the bus while rebooting by restoring all usb-related data to the initial values. Signed-off-by: Keith Packard <keithp@keithp.com>
* Revert "altos/stm: Run scheduler code on interrupt stack"Keith Packard2016-04-30
| | | | | | This reverts commit 6a9546413d6a236c010e806b50506d870961d074. This causes the device to stop reliably handling interrupts.
* altos/stm32l: Add support for software-driven HW flow controlKeith Packard2016-04-25
| | | | | | | | This allows applications to request that the flow control bits be driven from software rather than hardware, permitting more flexible pin configuration. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Use TXE instead of TC for serial on STM32lKeith Packard2016-04-25
| | | | | | | Using TXE allows for full-speed communication, rather than waiting for each byte to be transmitted before inserting the next into the queue. Signed-off-by: Keith Packard <keithp@keithp.com>
* Debug bits for telebtKeith Packard2016-04-25
|
* altos: Add ao_gpi_set/clr_bits functionsKeith Packard2016-04-13
| | | | | | These set or clear a group of bits in a single GPIO register all together. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add one-byte SPI output routine for LPC and STM coresKeith Packard2016-03-26
| | | | | | This allows for SPI output at interrupt time, one byte at a time. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Allow apps to define different stack sizeKeith Packard2016-03-26
| | | | | | | While 512 bytes is a reasonable size, sometimes apps don't have that much stack space. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Validate current task SP in interrupt by looking at PSPKeith Packard2016-03-26
| | | | | | | | | We use a separate stack pointer for task code, which means we can verify that it is in range in any interrupt handler. This adds checks for the task stack (under #ifdef DEBUG) that run in ao_wakeup as well as at every timer interrupt. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Run scheduler code on interrupt stackKeith Packard2016-03-26
| | | | | | This provides a bit more room for tasks on their stack Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Expose fast timer API from kernel/Keith Packard2016-03-18
| | | | | | This allows multiple SoCs to provide the same driver interface Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Get stm32l pwm driver workingKeith Packard2015-12-25
| | | | | | | | | | | | | Fix the CCMR1_OC1PE and CCMR2_OC3PE values. Disable clock when no PWM outputs are running. Fix the apb1enr value for the timer. Set ARR value to PWM_MAX - 1 -- ARR is off by one. Sets the GPIO pins to 40MHz bandwidth for sharper edges. Tested on EasyMega, but that code is not included as it breaks the companion protocol. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add TeleMega v2.0, including PWM driverKeith Packard2015-12-25
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Replace ao_alarm/ao_clear_alarm with ao_sleep_forKeith Packard2015-02-13
| | | | | | | | | | | | | | | | Having arbitrary alarms firing in the middle of complicated device logic makes no sense at all. Therefore only correct use of ao_alarm and ao_clear_alarm was around a specific ao_sleep call, with correct recovery in case the alarm fires. This patch replaces all uses of ao_alarm/ao_sleep/ao_clear_alarm with ao_sleep_for, a new function which takes the alarm timeout directly. A few cases which weren't simply calling ao_sleep have been reworked to pass the timeout value down to the place where sleep *is* being called, and having that code deal with the return correctly. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Add ability to delay STDIO usage for serial portsKeith Packard2015-02-01
| | | | | | | | Bluetooth needs to delay adding the serial port to stdio until the link is up and running. The cc1111 serial driver had DELAY_SERIAL_*_STDIN bits which have been added to the STM serial driver. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Fix typo in stm32l.hKeith Packard2015-01-26
| | | | | | This crept in while working on the stmf0 bits. oops. Signed-off-by: Keith Packard <keithp@keithp.com>
* ao-tools: Add --wait option to ao-usbloadKeith Packard2015-01-25
| | | | | | | This waits forever for USB writes to complete, instead of timing out after five seconds. Useful when debugging the device. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add support for TeleBT v3.0Keith Packard2015-01-24
| | | | | | | Add support to the BTM driver for non-CC1111 interrupts Add HW flow control to STM serial driver Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Mark STM ao_spi_send as taking const pointerKeith Packard2014-10-24
| | | | | | We don't write to this, so let it be const for type checking Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Rework packet receive for cc1120Keith Packard2014-07-05
| | | | | | | | | | Instead of blocking on PQT, just set up the receiver to start going and when the first bit interrupt comes in, grab the SPI bus if possible and configure it for reception. This improves sensitivity in the radio by a significant amount while making the code conceptually a bit nicer. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fake flight code changes in kernel and stmKeith Packard2014-05-27
| | | | | | | Redirects data input from local sensors to USB sourced data, leaving USB enabled when the computer goes into pad mode. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: stm and lpc ao_boot.h were identical. move to kernel.Keith Packard2014-05-15
| | | | | | | These two files were absolutely identical, so share them by moving under kernel instead.x Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Use explicit boot loader signal in ao_boot_rebootKeith Packard2014-05-15
| | | | | | | | Instead of just "knowing" that ao_boot_loader will be passed zero when the application wants to get back to the boot loader, explicitly define the values so that both sides always agree. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Use #define'd constants for GPIO register addressesKeith Packard2014-05-12
| | | | | | | This lets the compiler short-circuit the tests in ao_enable_gpio and ao_disable_gpio to save a bit of code space and time. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Figure out available flash space based on chip id registersKeith Packard2014-05-12
| | | | | | | Look at the flash size and the device id registers to figure out how much flash is available. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: White space fix in ao_boot_pin.cKeith Packard2014-05-12
|
* altos/stm: Use flash address of boot loader instead of 0x0Keith Packard2014-05-12
| | | | | | | Flash is at 0x08000000, but when the chip boots, it can be at 0x0 as well. Use the 0x08000000 address when rebooting to flash Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Simplify quadrature trackingKeith Packard2014-05-09
| | | | | | | | | | | | Set the timer to 200Hz for a 5ms debounce interval. Then, simply look for transitions ending in both bits in the encoder being off, which indicates the the encoder is resting in a detent. If bit '2' is turning off, the encoder was rotated clockwise, otherwise the encoder was rotated counter clockwise. This is a lot more reliable, although still not perfect. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Rename 'core' to 'kernel'Keith Packard2014-04-05
| | | | | | | core remains a bad name to use -- dirvish skips files (and directories, it seems) with that name. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Expose ao_usb_running globallyKeith Packard2014-02-18
| | | | | | This lets other bits of the code know when USB has been connected. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fixup named ADC printingKeith Packard2014-02-08
| | | | | | Print all ADC values on one line when using named ADC values Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Block interrupts while reprogramming flashKeith Packard2014-02-08
| | | | | | Wouldn't work well to get interrupted... Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Enable system timer in flash loader and prod watchdog with itKeith Packard2014-02-08
| | | | | | | This makes it possible to reflash the board without needing to disable the watchdog. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add names when reporting STM ADC valuesKeith Packard2014-02-08
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Report battery, apogee and main voltages over APRSKeith Packard2014-01-15
| | | | | | This makes APRS more usable when you mute the RF audio on the HT. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Turn on -Werror for STM and LPC buildsKeith Packard2013-12-20
| | | | | | | Now that the build completes with no warnings, make future warnings into errors. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Turn on -WextraKeith Packard2013-12-20
| | | | | | All of the warnings for STM projects are cleaned up now Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Clean up -Wextra warningsKeith Packard2013-12-20
| | | | | | | Unused variables, mismatching signed/unsigned and a few other misc warnings. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Turn on -Wall for stm compilesKeith Packard2013-12-20
| | | | | | The warnings are all cleaned up now, leave this on by default Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Clean up some minor warnings from -WallKeith Packard2013-12-20
| | | | | | Unused variables, functions and labels, missing enums in switch. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Semantic error in STM usb disable caused it to not workKeith Packard2013-12-18
| | | | | | | The USB enable register wasn't actually getting rewritten with the enable bit turned off, so the USB device was still powered on in flight. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: Update pdclib paths for flash-loader buildsKeith Packard2013-12-18
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Build pdclib locally if necessaryKeith Packard2013-12-18
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Use all 16 bits of setup packet len when limiting reply lenKeith Packard2013-12-17
| | | | | | | | | We were only using the low 8 bits of the setup packet reply max len, which meant that if the other side sent a weird max len (as Windows 7 does), then we'd truncate our setup reply to whatever was in the low 8 bits of that value. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos/stm: arm-none-eabi-binutils now puts 'main' into .text.startupKeith Packard2013-12-08
| | | | | | | | Change name of .text.ram to .ramtext, then load .text* into flash and .ramtext into ram. This ensures that 'main' and anything else in a random .text.* segment will get loaded into flash as appropriate. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Change flash loader name to just AltosFlashKeith Packard2013-12-08
| | | | | | Remove the software version string from the product name Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Build .ihx files for all arm projectsKeith Packard2013-12-08
| | | | | | The .ihx version can be processed by the java loader Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Allow use of internal EEPROM for config storageKeith Packard2013-11-12
| | | | | | | | | | | This stops exposing eeprom as 'storage' and instead exposes it with a separate eeprom API so that it can be used for config storage without also using it for flight log storage. The config code has been changed to allow it to either use storage for configuration data or eeprom. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add gyro-based orientation trackingKeith Packard2013-10-25
| | | | | | | This tracks the angle-from-vertical as an additional input to the pyro channels. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Use installed pdclibKeith Packard2013-10-10
| | | | | | Switch over to the installed pdclib everywhere Signed-off-by: Keith Packard <keithp@keithp.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-11-03 04:49:08 +0000