mjb/altos - AltOS - the operating system for Altus Metrum products

	Commit message (Collapse)	Author	Age
*	altos: Oopsed the STM DMA channels for I2C1	Keith Packard	2012-04-25
\| \| \| \| \| \|	TX is 6, RX is 7 Signed-off-by: Keith Packard <keithp@keithp.com>
*	altos: Starting to write cc1120 driver	Keith Packard	2012-04-17
\| \| \| \| \| \| \|	This does "something" in radio test mode, appearing to generate a 730MHz signal. Signed-off-by: Keith Packard <keithp@keithp.com>
*	altos: Add register definitions for STM syscfg and usb	Keith Packard	2012-04-14
\| \| \| \|	Signed-off-by: Keith Packard <keithp@keithp.com>
*	altos: Make STM clock configuration per-product. Fix 32MHz CPU speed	Keith Packard	2012-04-09
\| \| \| \| \| \| \| \| \| \|	This moves all of the STM clock configuration into ao_pins.h so that each product can configure it separately. While doing this, I discovered that the flash memory mode (64-bit, prefetch, latency 1) wasn't actually getting set, which is why the CPU refused to work at 32MHz. Signed-off-by: Keith Packard <keithp@keithp.com>
*	altos: Add beeper driver to STM arch	Keith Packard	2012-04-09
\| \| \| \| \| \|	Drives the MegaMetrum beeper Signed-off-by: Keith Packard <keithp@keithp.com>
*	altos: add STM I2C driver.	Keith Packard	2012-04-09
\| \| \| \| \| \|	Not well tested yet... Signed-off-by: Keith Packard <keithp@keithp.com>
*	altos: Add STM temperature sensor calibration data	Keith Packard	2012-04-07
\| \| \| \| \| \| \|	Each stm32l has two-point factory temperature calibration data. Provide access to that for displaying temperature data. Signed-off-by: Keith Packard <keithp@keithp.com>
*	altos: Add support for STM ADC	Keith Packard	2012-04-07
\| \| \| \| \| \|	DMA-based driver for the STM analog to digital converter. Signed-off-by: Keith Packard <keithp@keithp.com>
*	altos: Declare stm DMA address registers as volatile void *	Keith Packard	2012-04-06
\| \| \| \| \| \|	Eliminates a cast when assigning to them. Signed-off-by: Keith Packard <keithp@keithp.com>
*	altos: Add DMA, SPI and MS5607 drivers	Keith Packard	2012-04-06
\| \| \| \|	Signed-off-by: Keith Packard <keithp@keithp.com>
*	Automatically set ALTERNATE pin mode when setting alternate function	Keith Packard	2012-03-28
\| \| \| \| \| \| \|	When selecting an alternate function, set the pin to alternate mode as well; there's no sense requiring two separate calls everywhere. Signed-off-by: Keith Packard <keithp@keithp.com>
*	Add defines for LCD controller and RTC clocking	Keith Packard	2012-03-28
\| \| \| \|	Signed-off-by: Keith Packard <keithp@keithp.com>
*	Add support for multiple serial ports on STM32L	Keith Packard	2012-03-28
\| \| \| \|	Signed-off-by: Keith Packard <keithp@keithp.com>
*	Basic OS running on STM32L	Keith Packard	2012-03-28
\| \| \| \| \| \|	This gets stm-demo working Signed-off-by: Keith Packard <keithp@keithp.com>
*	Add stm-demo program	Keith Packard	2012-03-28
\| \| \| \| \| \|	This runs AltOS and talks over the serial port. Signed-off-by: Keith Packard <keithp@keithp.com>
*	Add STM platform and stm-bringup demo program	Keith Packard	2012-03-28
	The stm-bringup doesn't run altos, it just initializes the device and writes stuff over a serial port. Works on the STM32L Discovery board at least, should do stuff on other boards too. Signed-off-by: Keith Packard <keithp@keithp.com>