| Commit message (Collapse) | Author | Age |
|---|
| |
|
|
|
|
|
|
|
| |
Generates vsync/hsync using timers and pixel data using the SPI port.
320x240 video using 640x480 mode and a 24MHz "pixel" clock.
Includes the beginings of rendering code for the frame buffer,
including bitblt, solid fill and text with a 5x7 font.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
Make sure receive DMA is higher than any TX dma so that
it always runs in preference.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| |
Having arbitrary alarms firing in the middle of complicated device
logic makes no sense at all. Therefore only correct use of ao_alarm
and ao_clear_alarm was around a specific ao_sleep call, with correct
recovery in case the alarm fires.
This patch replaces all uses of ao_alarm/ao_sleep/ao_clear_alarm with
ao_sleep_for, a new function which takes the alarm timeout directly.
A few cases which weren't simply calling ao_sleep have been reworked
to pass the timeout value down to the place where sleep *is* being
called, and having that code deal with the return correctly.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
Unused variables, functions and labels, missing enums in switch.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| | |
|
| |
|
|
|
|
| |
Stop using cli/sei, which are avr-specific
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
Fix both clock time and rise time.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
|
|
| |
This slows the i2c bus to 100kHz (yuck), sets the rise time to spec
(it was way off) and adds more delays during bus setup. I've run this
for hours now without trouble. Will try to adjust things back to fast
mode and see if I can make that work as 100kHz isn't fast enough to
reliably get data at 100 samples/sec.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
| |
This seems better than the random loop that it replaces, but I still
have no idea why this is required; it doesn't coorespond to the docs
at all...
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
|
| |
The fancy stm i2c debugging code had calls to flush() that were
invoked outside of the conditionals leading to all kinds of fun --
flush() may re-enable interrupts, yield or do all kinds of wacky
stuff, none of which is appropriate from the middle of a device driver
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
I have no idea why this is required, but the mpu6000 will not come up
and run if this isn't present.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
In case it's wedged.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
This waits for the stop signal to appear on the bus, necessary before
starting another transaction.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
| |
Transaction appears to be clean on the i2c bus now; correct number of
bytes received, and the nack and stop at the right time. This tests >
2 length reads; should try that too.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
| |
Start now driven by interrupts
Send now done with DMA and interrupts
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
Recv doesn't appear to work with more than one byte
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
Not well tested yet...
Signed-off-by: Keith Packard <keithp@keithp.com>
|
