summaryrefslogtreecommitdiff
path: root/src/stm/ao_arch.h
Commit message (Collapse)AuthorAge
* altos: Increase default STM stack to 648 bytesKeith Packard2012-06-27
| | | | | | | 512 seems cozy given the printf implementation we're using and the extensive interrupts. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Optimize FEC encode and decodeKeith Packard2012-06-26
| | | | | | | | | | | | | Integrate interleaving, CRC and padding within the decode/encode functions. Provide for ISR priorities so that the 1120 RX interrupt takes precedence over the other interrupts or we risk losing bits. Optimize the viterbi decoder a bit (goes from 10ms per packet to 7ms per packet). Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Be more careful about register save/restore in ao_yieldKeith Packard2012-06-17
| | | | | | | Make sure the general registers are all saved before messing with any of them. Then, explicitly use r0 to save/restore apsr and primask. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Massive product config cleanupKeith Packard2012-04-14
| | | | | | | | Support multiple serial ports more cleanly Split out parts of ao.h into separate feature header files Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add STM ao_arch_reboot implementationKeith Packard2012-04-14
| | | | | | Uses the AIRCR register to force a reset Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make STM clock configuration per-product. Fix 32MHz CPU speedKeith Packard2012-04-09
| | | | | | | | | | This moves all of the STM clock configuration into ao_pins.h so that each product can configure it separately. While doing this, I discovered that the flash memory mode (64-bit, prefetch, latency 1) wasn't actually getting set, which is why the CPU refused to work at 32MHz. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add support for STM ADCKeith Packard2012-04-07
| | | | | | DMA-based driver for the STM analog to digital converter. Signed-off-by: Keith Packard <keithp@keithp.com>
* Get config stuff hooked up for MegaMetrumKeith Packard2012-03-28
| | | | | | This stubs out enough stuff to let ao_config link and work Signed-off-by: Keith Packard <keithp@keithp.com>
* Use 16-bits for STM32 LED mask. Export serial I/O functionsKeith Packard2012-03-28
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* Allow any STM usart to be used for stdioKeith Packard2012-03-28
| | | | | | | This also adds the alternate pin configurations for the other two usarts Signed-off-by: Keith Packard <keithp@keithp.com>
* Move LCD string output code to ao_lcd_font.cKeith Packard2012-03-28
| | | | | | | It's all very specific to the 14-segment display, so stick it there. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add LCD device driver to STM32L portKeith Packard2012-03-28
| | | | | | | This enables the 6-digit 14-character display on the STM32L discovery board and provides an ascii output to it. Signed-off-by: Keith Packard <keithp@keithp.com>
* Save/restore PRIMASK register on Cortex-M3Keith Packard2012-03-28
| | | | | | This preserves the interrupt-enabled bit across context switches Signed-off-by: Keith Packard <keithp@keithp.com>
* Basic OS running on STM32LKeith Packard2012-03-28
| | | | | | This gets stm-demo working Signed-off-by: Keith Packard <keithp@keithp.com>
* Add stm-demo programKeith Packard2012-03-28
| | | | | | This runs AltOS and talks over the serial port. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add STM platform and stm-bringup demo programKeith Packard2012-03-28
The stm-bringup doesn't run altos, it just initializes the device and writes stuff over a serial port. Works on the STM32L Discovery board at least, should do stuff on other boards too. Signed-off-by: Keith Packard <keithp@keithp.com>
generated by cgit v1.2.3 (git 2.39.1) at 2026-07-29 12:20:04 +0000