summaryrefslogtreecommitdiff
path: root/src/stm-demo/ao_pins.h
Commit message (Collapse)AuthorAge
* altosui: Hide Tilt Angle values when not availableKeith Packard2014-03-10
| | | | | | | In the Ascent table, make sure the tilt angle fields are hidden when they are set to MISSING. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Clean up boot loader supportKeith Packard2013-05-07
| | | | | | | Split out code into separate files. Add support for getting back to boot loader from application. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Set STM GPIO output speed for SPI pins correctlyKeith Packard2013-01-13
| | | | | | | | The GPIO pin settings affect the output impedence, and hence the maximum speed for SPI. Cranking these to suitable values allows SPI to run at full speed. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Specify the LCD duty cycle for stm-demoKeith Packard2012-08-27
| | | | | | This is the demo for the large 7-segment displays and needs static drive Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add button driver and event queueKeith Packard2012-08-06
| | | | | | | With this, a single task can wait for any button or quadrature input device. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Support multiple quadrature encoders.Keith Packard2012-08-06
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Fix up quadrature driverKeith Packard2012-08-06
| | | | | | Mostly works now, should work reliably with a bit of input filtering. Signed-off-by: Keith Packard <keithp@keithp.com>
* Signed-off-by: Keith Packard <keithp@keithp.com>Keith Packard2012-08-06
| | | | altos: Test quadrature driver
* altos: Clean up usage of port parametersKeith Packard2012-06-26
| | | | | | | | Make stm port parameters always be pointers; this avoids the confusion where some macros took '&port' and others took a bare 'port', and also unifies code to run on other processors in a consistent fashion. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make stm-demo compile with new ao_data structureKeith Packard2012-05-27
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Switch stm-demo to HSE clock, add USBKeith Packard2012-04-14
| | | | | | | Requires that SB17 be soldered shut so that the MCO from the STlink CPU is available the target for HSE input. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Make STM clock configuration per-product. Fix 32MHz CPU speedKeith Packard2012-04-09
| | | | | | | | | | This moves all of the STM clock configuration into ao_pins.h so that each product can configure it separately. While doing this, I discovered that the flash memory mode (64-bit, prefetch, latency 1) wasn't actually getting set, which is why the CPU refused to work at 32MHz. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Test I2C code on discovery board.Keith Packard2012-04-09
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Show temperature in stm-demoKeith Packard2012-04-07
| | | | | | Use the ADC to show current temperature Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add ADC tests to stm-demoKeith Packard2012-04-07
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add DMA, SPI and MS5607 driversKeith Packard2012-04-06
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* Make stm-demo display a scrolling messageKeith Packard2012-03-28
| | | | | | | Instead of trying to frob the LEDs, which are now owned by the serial port. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add LCD device driver to STM32L portKeith Packard2012-03-28
| | | | | | | This enables the 6-digit 14-character display on the STM32L discovery board and provides an ascii output to it. Signed-off-by: Keith Packard <keithp@keithp.com>
* Add support for multiple serial ports on STM32LKeith Packard2012-03-28
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* Fix STM LED driver and blink LEDs on discovery boardKeith Packard2012-03-28
| | | | | | | | This adds a task to blink the LEDs, after first fixing up the LED output code to enable the GPIO and talk to the right pins for the discovery board. Signed-off-by: Keith Packard <keithp@keithp.com>
* Basic OS running on STM32LKeith Packard2012-03-28
| | | | | | This gets stm-demo working Signed-off-by: Keith Packard <keithp@keithp.com>
* Add stm-demo programKeith Packard2012-03-28
This runs AltOS and talks over the serial port. Signed-off-by: Keith Packard <keithp@keithp.com>
generated by cgit v1.2.3 (git 2.39.1) at 2025-11-03 04:41:27 +0000