summaryrefslogtreecommitdiff
path: root/src/cc1111/ao_pins.h
Commit message (Collapse)AuthorAge
* altos: Add telefire-v0.1Keith Packard2012-07-29
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Force 434.550Mhz by connecting debug gnd and clk (trac #41)Keith Packard2012-07-10
| | | | | | | | Check for pin P2_2 low at startup and set the frequency to 434.550MHz. This value won't get written to flash, so rebooting again will restore the configured frequency. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Clean up usage of port parametersKeith Packard2012-06-26
| | | | | | | | Make stm port parameters always be pointers; this avoids the confusion where some macros took '&port' and others took a bare 'port', and also unifies code to run on other processors in a consistent fashion. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove unused AES code from teledongle and tidongleKeith Packard2012-06-04
| | | | | | Leave this out as neither of these products need it. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: All cc1111 products have a radioKeith Packard2012-05-28
| | | | Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Massive product config cleanupKeith Packard2012-04-14
| | | | | | | | Support multiple serial ports more cleanly Split out parts of ao.h into separate feature header files Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add support for multiple SPI busses and sharing device driversKeith Packard2012-04-14
| | | | | | | | | | | | | | | | The STM32L151 has several SPI busses, and we want to use more than one, so add a 'bus' parameter to the SPI interfaces. To avoid wasting time on AVR and CC1111 processors which only use one SPI bus, elide those parameters from the actual functions by wrapping them with macros. Configuring chip select is now all macroized so that each chip can have its own version, allowing the STM to share the various SPI device drivers with the cc1111 and avr processors. Note that only the M25 driver has been ported; porting the others is 'trivial', but not necessary at this point. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Create TeleMetrum v1.2 directoryKeith Packard2011-12-17
| | | | | | | The hardware is software-compatible with v1.1, but it's nice to have the right version number in all of the files. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Set default flight log max to 127k on TM v0.1Keith Packard2011-11-12
| | | | | | The flash part on v0.1 boards is only 128kB. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Handle internal and external telem monitoring requestsKeith Packard2011-11-12
| | | | | | | | | | | | Record separate internal vs external monitoring state, allowing both to happen at the same time, and when either is turned off, the other keeps working. This also adds disable/enable so that other radio users can temporarily take over the radio; monitoring will resume when the other radio user is finished. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Add LEGACY_MONITOR defines to more programsKeith Packard2011-10-15
| | | | | | | Make all monitoring programs define whether they want all of the old telemetry formats too. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Improve TM v1.0 apogee estimateKeith Packard2011-10-08
| | | | | | | | | | | | | | | | | | | | | v1.0 boards have noisy accelerometer data caused by interactions between RF transmission and the accelerometer measurements; this noise generates a negative bias in the accelerometer readings. The net effect is that the estimated speed is lower than the actual speed, causing early an apogee estimate. By increasing the sigma value for accelerometer data, the kalman filter 'trusts' the acceleration data less, putting more weight on the barometer data. This causes the estimated time of apogee to be closer to the correct value. This reduces the response to changes in acceleration. This new value is applied solely to TeleMetrum v1.0 boards. v1.1 boards correct for this error, and hence can use the correct sigma value for the accelerometer. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Report continuity in telebtKeith Packard2011-08-28
| | | | | | Report continuity values from remote altimeter Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Remove RSSI reporting from telebtKeith Packard2011-08-28
| | | | | | | Telebt uses one LED for bluetooth connection and the other for telem packet reception leaving none for RSSI. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: move igniter defines back to ao_pins.hKeith Packard2011-08-27
| | | | | | so that ao_launch gets them too Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Get AES CBC-MAC packet transfers runningKeith Packard2011-08-27
| | | | | | | | | This just has simple command-line based packet transfers for testing. This also adds special ao_telelaunch bits where the launch control code will live. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Start work on AES and raw radio interfaces.Keith Packard2011-08-27
| | | | | | We probably don't want this raw radio interface, but it's a start. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: Start telelaunch productKeith Packard2011-08-27
| | | | | | Looks a lot like TM, but without the flight code. Signed-off-by: Keith Packard <keithp@keithp.com>
* altos: add GCC/SDCC compat macros, init_stack, save_context and GCC stdio hooksKeith Packard2011-08-25
More arch-indepdency bits. GCC stdio is different from SDCC, so create suitable code in avr/ao_avr_stdio.c Create macros to initialize the task stack frame and save the task context. Add GCC/SDCC type definition compatibility macros Signed-off-by: Keith Packard <keithp@keithp.com>
generated by cgit v1.2.3 (git 2.39.1) at 2026-06-03 19:43:00 +0000