| Commit message (Collapse) | Author | Age |
|
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
|
|
| |
Move most of the 1.2 content to the 1.2.1 block
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
|
|
|
| |
This is almost all identical to AltosUI; I think we'll want to share
the two sections.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
|
|
| |
Not much content yet, but I think this is pretty much the sections we need
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
|
|
|
|
| |
TeleMini needs emergency recovery mode in case you forget the radio
parameters and need to get things back to a known state. Add
documentation to describe what this does and how to get it enabled.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
| |
|
| |
|
|
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
|
|
| |
This makes it easy to see which changes are from each version of the software.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
|
|
|
|
| |
Looks like the 'standard' polarity for 3.7V lipos using JST connectors
in RC aircraft is swapped from what Spark Fun uses. Note that in the
docs to try and keep people from wrecking hardware.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
|
|
| |
What it says on the tin.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
|
| |
The hardware is software-compatible with v1.1, but it's nice to have
the right version number in all of the files.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|\
| |
| |
| |
| | |
Conflicts:
doc/altusmetrum.xsl
|
| |
| |
| |
| |
| |
| |
| | |
This was described in detail in both the System Operation and AltosUI
chapters. Remove the duplicate from the AltosUI chapter.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |\ |
|
| | |
| | |
| | |
| | |
| | |
| | | |
These describe what these configuration parmaeters do, not how to set them.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |/
|/| |
|
|\|
| |
| |
| |
| | |
Conflicts:
doc/altusmetrum.xsl
|
| |
| |
| |
| | |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|/ |
|
|\ |
|
| |
| |
| |
| |
| |
| | |
The Flash Image paragraph references it, change the reference wording.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
| |
| |
| |
| |
| |
| | |
This isn't central to operation of the devices, so move it out to a
separate chapter
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|/ |
|
|\ |
|
| |
| |
| |
| |
| |
| |
| | |
Make sure 'radio link' doesn't refer to telemetry and eliminate use of
'RF link' and other similar but not identical phrases.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|/ |
|
| |
|
|\ |
|
| |
| |
| |
| |
| |
| | |
It makes far more sense here.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
| |
| |
| |
| |
| |
| |
| | |
Include comments about TeleMini in the introduction, and then explain
a bit better what the best method of reliably initiating packet
command mode are (start operation, then boot telemini).
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|/ |
|
| |
|
|
|
|
|
|
| |
There wasn't any documentation for this field in the 'Launch Pad' tab.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
|
|
| |
Lots of minor spelling errors.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
| |
|
|
|
|
|
|
|
| |
Tiny netbooks aren't tall enough for the 'usual' font size, so provide
a smaller option. Then provide a bigger option, just because.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
|
|
|
| |
Document installation suggestions, including mounting, RFI, antenna
issues and ground testing.
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
| |
Signed-off-by: Keith Packard <keithp@keithp.com>
|
|
|
|
|
|
|
| |
This adds release notes and includes them in the main altusmetrum doc
as well as making stand-alone html available for inclusion in the website.
Signed-off-by: Keith Packard <keithp@keithp.com>
|