summaryrefslogtreecommitdiff
Commit message (Expand)AuthorAge
...
* Stop log dumping at flight end. Print 'end' at end of log.Keith Packard2009-06-03
* Start adding bi-directional packet linkKeith Packard2009-05-31
* Eliminate RDF tone generation.Keith Packard2009-05-28
* Change .gitignore to match new aoload procedureKeith Packard2009-05-28
* Leave serial number writing to aoloadKeith Packard2009-05-27
* Fix aoview telemetry GPS parsing code to use correct columnsKeith Packard2009-05-23
* Parse both telemetry or log data ao_flight_testKeith Packard2009-05-23
* Avoid 16-bit overflow in velocity computation.Keith Packard2009-05-23
* Make file handling more general so it can be reused.Keith Packard2009-05-20
* Ignore aoview_glade.hKeith Packard2009-05-17
* Transmit computed ground pressure and acceleration values0.4Keith Packard2009-05-17
* Provide install targetKeith Packard2009-05-17
* Embed glade file in executableKeith Packard2009-05-17
* Add About dialog to aoview.Keith Packard2009-05-17
* USB device names can contain '.' tooKeith Packard2009-05-17
* scandir returns -1 on errorKeith Packard2009-05-17
* Send computed accel/vel/pres values over the radio0.3Keith Packard2009-05-17
* Handle disappearing serial devicesKeith Packard2009-05-17
* While on the pad, zero out velocity every secondKeith Packard2009-05-17
* Clear table, reset log on disconnectKeith Packard2009-05-17
* Add pad lat/lon, max accel, max heightKeith Packard2009-05-17
* Clean up GPS displayKeith Packard2009-05-17
* Make aoview window tallerKeith Packard2009-05-17
* Add lots more aoview UI bitsKeith Packard2009-05-17
* When logging starts up, right the whole ring to the log.Keith Packard2009-05-16
* Abandon use of accelerometer for apogee detect.Keith Packard2009-05-16
* Add preliminary aoview codesn4-flight2sn4-flight1Keith Packard2009-05-16
* Discard usb output before connection. Handle USB reset.0.2Keith Packard2009-05-13
* Enable radio monitor by default in teleterra, teledongle and tidongleKeith Packard2009-05-13
* Remove monitor/rssi functions from telemetrum loadKeith Packard2009-05-13
* Split out ao_state_names to separate fileKeith Packard2009-05-13
* Indicate RSSI with a blinking LEDKeith Packard2009-05-13
* Make ao_flight_test show AGL altitude and positive acceleration under boostKeith Packard2009-05-13
* Make ao_flight_test able to read raw logging dataKeith Packard2009-05-13
* Print only RSSI when packet CRC is invalidKeith Packard2009-05-13
* Accelerometer-based velocity values are invalid after apogeeKeith Packard2009-05-13
* Add velocity check for boost detect via accelerometerKeith Packard2009-05-13
* Typo in callsignKeith Packard2009-05-13
* Use recorded accelerometer baseline data in ao_flight_testKeith Packard2009-05-10
* Don't re-initialize the landing range data at each apogee detect sampleKeith Packard2009-05-10
* Initialize ao_min_vel with |ao_flight_vel|Keith Packard2009-05-10
* Decrease telemetry rate on the pad to 1/sec instead of 20/secKeith Packard2009-05-10
* Increase the initial accel/baro average to 1000 samplesKeith Packard2009-05-10
* Record average accelerometer value in flight start log recordKeith Packard2009-05-10
* Add version command to show product informationKeith Packard2009-05-09
* Pad callsign with nulsKeith Packard2009-05-09
* USB spec limits bulk endpoints to 64 byte payload max.Keith Packard2009-05-01
* Use 'char' instead of 'uint8_t' for character dataKeith Packard2009-04-29
* Eliminate incorrect cast in printf string argumentKeith Packard2009-04-29
* Correct radio frequency shown in config display.Keith Packard2009-04-29
generated by cgit v1.2.3 (git 2.39.1) at 2026-03-26 13:49:23 +0000