mjb/altos/src, branch altosui-ms5611AltOS - the operating system for Altus Metrum products
https://git.ethernal.org/mjb/altos/atom?h=altosui-ms56112012-11-02T00:52:22+00:00altos: Build megadongle when possible2012-11-02T00:52:22+00:00Keith Packardkeithp@keithp.com2012-11-02T00:52:22+00:00urn:sha1:b3205a1d246e5ed229256aa787f26e6e122b7a2f
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/megadongle: Add megadongle product2012-11-01T17:51:41+00:00Keith Packardkeithp@keithp.com2012-11-01T17:51:41+00:00urn:sha1:793b950083d09ead4f6230e041ad43aa9f5f2179
Looks a lot like teledongle from a feature perspective.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Remove legacy telemetry from ao_monitor when not needed2012-11-01T17:50:03+00:00Keith Packardkeithp@keithp.com2012-11-01T17:50:03+00:00urn:sha1:f74d724f92b335d6c0674d0f1fcc650b729401df
For products not supporting LEGACY_MONITOR, remove the (undefined)
structs from the ao_monitor union.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Remove 'volatile' from ao_rssi.c globals2012-11-01T17:49:17+00:00Keith Packardkeithp@keithp.com2012-11-01T17:49:17+00:00urn:sha1:e4d931cd99a7c91803584b71670e30c0d00217df
No need for this, the variables aren't changed at interrupt time.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/stm: Support LEDs on multiple ports2012-11-01T17:48:08+00:00Keith Packardkeithp@keithp.com2012-11-01T17:48:08+00:00urn:sha1:86f8b92149d1027b1d6d6b1cae097cfe47b02090
Split out the bits in a fairly simplistic fashion so that we support
no more than 16 LEDs still.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/attiny: Remove debugging code which frobs PB12012-10-31T04:31:27+00:00Keith Packardkeithp@keithp.com2012-10-31T02:56:51+00:00urn:sha1:fcdaa0d748058a7f52a1bdc1a1627dc394762e5a
This was clearly stuck there to debug something; not a good idea...
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/micropeak: Run MS5607 at max resolution for micropeak2012-10-31T04:31:27+00:00Keith Packardkeithp@keithp.com2012-10-31T02:44:45+00:00urn:sha1:af8cb40851a5cf5e3bd06ddd85e4e2df16bfbad2
We've got lots of time, so get the highest resolution baro data available.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/micropeak: Clock micropeak at 250kHz to save power2012-10-31T02:41:08+00:00Keith Packardkeithp@keithp.com2012-10-31T02:41:08+00:00urn:sha1:371da0c909098092db7b596496df9d58eed43703
This reduces average current consumption from 2mA to .4mA. This
makes the battery last longer, but also gets the current under
something that the typical CR1025 battery can support. Would be nice
to reduce current even further; cheap CR1025 batteries still seem to
fade a bit at this current level.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/attiny: Don't initialize the CS pin in the general SPI setup2012-10-31T02:39:55+00:00Keith Packardkeithp@keithp.com2012-10-31T02:39:55+00:00urn:sha1:e8a4a00a5bb333d4ee9601d53242a82dfe0372c2
Let the CS pin be configured by the driver, which can set the correct
value before enabling the output.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/micropeak: Set boost detect to 10m. Add 30s boost delay.2012-10-30T00:13:23+00:00Keith Packardkeithp@keithp.com2012-10-30T00:07:05+00:00urn:sha1:f7d2613bb0a6ab1c63e3f6252a3a2358fdfbc691
Wait for 30 seconds before even starting look for boost. This provides
an opportunity to close up the airframe, potentially causing pressure
gradients seen by the baro sensor.
Also, require a 10m vertical motion before triggering boost. This
should limit accidental boost detect while capturing any actual flights.
Signed-off-by: Keith Packard <keithp@keithp.com>