mjb/altos/src/telemini-v3.0, branch debian/1.8.7-1AltOS - the operating system for Altus Metrum products
https://git.ethernal.org/mjb/altos/atom?h=debian%2F1.8.7-12017-05-05T05:10:36+00:00altos/telemini-v3.0: Use dbg connector pin 5 for force bootloader2017-05-05T05:10:36+00:00Keith Packardkeithp@keithp.com2017-05-05T05:09:31+00:00urn:sha1:08da6f2100c0241c70554427e53b7e237dfda16c
This works way better than attempting to use the beeper pin.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Add 'recovery mode' on PA14 (pin 6 on dbg header)2017-05-05T05:10:36+00:00Keith Packardkeithp@keithp.com2017-05-05T05:07:51+00:00urn:sha1:178d7c0aa32267ea71be2ccff146ea6ff990d7dc
Connect this pin to GND (pin 3) and TeleMini will come up with N0CALL
at 434.550MHz using the original frequency calibration. Helps recover
from accidental mis-configuration.
Signed-off-by: Keith Packard <keithp@keithp.com>
telemini-v3.0: make git ignore build products2017-04-26T05:06:34+00:00Bdale Garbeebdale@gag.com2017-04-26T05:06:34+00:00urn:sha1:2b014fe9fa64e7aead586bc682251346d000c8ccaltos/telemini-v3.0: Fix license2017-04-25T05:01:38+00:00Keith Packardkeithp@keithp.com2017-04-25T04:54:25+00:00urn:sha1:43cf1991f042e50fb6ec0b037f6d212436e3d31b
Was GPL2, switch to GPL2+
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Remove vestiges of the pre-USB code2017-04-22T00:04:28+00:00Keith Packardkeithp@keithp.com2017-04-22T00:04:28+00:00urn:sha1:77c76e429074a53c1c5230a7b5e665d1715b296f
Pre-USB telemini v3 designs had a separate firmware load for radio
calibration. Now that we've got enough USB to perform flash/cal/test,
we don't need that other firmware load, so we can remove the remaining
Makefile remnants of the calibration load.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Add flash loader2017-04-20T06:08:56+00:00Keith Packardkeithp@keithp.com2017-04-20T06:08:56+00:00urn:sha1:7db49a2052ec905cdc02f626c0933ca6889d64a4
Now that telemini has USB, use the boot loader to make it easy to
update firmware.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Update to production hardware2017-04-20T06:08:06+00:00Keith Packardkeithp@keithp.com2017-04-20T06:08:06+00:00urn:sha1:d1ba276c6e54564f82920f65bf4c19df85c9ea56
Removed LEDs. Added USB. Flipped lots of pins around.
This appears to make telemini work.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Add beeper defines needed for more general beeper code2017-02-21T01:35:26+00:00Keith Packardkeithp@keithp.com2017-02-21T01:33:37+00:00urn:sha1:3c3f5e316c0c2464568db883d50881f5b898abac
The beeper code now wants to know which timer, port and pin are in use.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Swap main and apogee sense pins.2017-02-20T19:16:53+00:00Keith Packardkeithp@keithp.com2017-02-20T01:40:28+00:00urn:sha1:5c272d8e50d0b23f31a6a9ebdad81fc514936222
These were just hooked up wrong in the software.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Split out TeleMini v3 log/telem labeling2017-02-20T19:16:53+00:00Keith Packardkeithp@keithp.com2017-02-20T01:39:21+00:00urn:sha1:59ac667c4ae14e0fa699fb0f398d31763a237646
Allow the ground software to know which TeleMini version is in use,
even though they are very similar with only ADC values differing.
Signed-off-by: Keith Packard <keithp@keithp.com>