mjb/altos/src/telemini-v3.0/ao_pins.h, branch masterAltOS - the operating system for Altus Metrum products
https://git.ethernal.org/mjb/altos/atom?h=master2018-10-19T15:38:32+00:00altos/stm: Make beeper driver support all possible tim234 configs2018-10-19T15:38:32+00:00Keith Packardkeithp@keithp.com2018-10-13T20:42:34+00:00urn:sha1:dbc52686c6d9808275c35e0c9c987cbbd9f7859d
And update all users to be explicit about the desired config.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Eliminate 'pin' field from GPIO functions2018-10-13T15:23:25+00:00Keith Packardkeithp@keithp.com2018-09-11T17:40:24+00:00urn:sha1:cdaa0d7b272505c49017f409b7c0b8e3240608f0
This was used with the 8051 bit-addressing mode to provide
single-instruction access to GPIO pins.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Add 'recovery mode' on PA14 (pin 6 on dbg header)2017-05-05T05:10:36+00:00Keith Packardkeithp@keithp.com2017-05-05T05:07:51+00:00urn:sha1:178d7c0aa32267ea71be2ccff146ea6ff990d7dc
Connect this pin to GND (pin 3) and TeleMini will come up with N0CALL
at 434.550MHz using the original frequency calibration. Helps recover
from accidental mis-configuration.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Fix license2017-04-25T05:01:38+00:00Keith Packardkeithp@keithp.com2017-04-25T04:54:25+00:00urn:sha1:43cf1991f042e50fb6ec0b037f6d212436e3d31b
Was GPL2, switch to GPL2+
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Update to production hardware2017-04-20T06:08:06+00:00Keith Packardkeithp@keithp.com2017-04-20T06:08:06+00:00urn:sha1:d1ba276c6e54564f82920f65bf4c19df85c9ea56
Removed LEDs. Added USB. Flipped lots of pins around.
This appears to make telemini work.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Add beeper defines needed for more general beeper code2017-02-21T01:35:26+00:00Keith Packardkeithp@keithp.com2017-02-21T01:33:37+00:00urn:sha1:3c3f5e316c0c2464568db883d50881f5b898abac
The beeper code now wants to know which timer, port and pin are in use.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Swap main and apogee sense pins.2017-02-20T19:16:53+00:00Keith Packardkeithp@keithp.com2017-02-20T01:40:28+00:00urn:sha1:5c272d8e50d0b23f31a6a9ebdad81fc514936222
These were just hooked up wrong in the software.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Split out TeleMini v3 log/telem labeling2017-02-20T19:16:53+00:00Keith Packardkeithp@keithp.com2017-02-20T01:39:21+00:00urn:sha1:59ac667c4ae14e0fa699fb0f398d31763a237646
Allow the ground software to know which TeleMini version is in use,
even though they are very similar with only ADC values differing.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Finish initial turn-on2017-02-20T19:16:53+00:00Keith Packardkeithp@keithp.com2017-02-19T06:56:49+00:00urn:sha1:c75736c9cd8f869c257a3024efda843cf0edf2a3
TeleMini v3.0 is nearly working; there are some ADC issues still, and
lots of altosui work left to decode the new telemetry packet.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telemini-v3.0: Update to second prototype version2017-02-20T19:16:53+00:00Keith Packardkeithp@keithp.com2017-02-03T05:52:57+00:00urn:sha1:efdeb402d04e7f04ad4bd2764f8f1ca7270b3dff
Separate radio xtal means we run the processor at 48MHz.
Fix the battery monitoring voltage divider resistor values.
Disable most of the code until we've got the radio working.
Signed-off-by: Keith Packard <keithp@keithp.com>