mjb/altos/src/telefire-v0.1/ao_pins.h, branch masterAltOS - the operating system for Altus Metrum products
https://git.ethernal.org/mjb/altos/atom?h=master2018-10-13T15:21:58+00:00altos: Remove cc1111 products2018-10-13T15:21:58+00:00Keith Packardkeithp@keithp.com2018-08-05T04:17:19+00:00urn:sha1:56629222711ba3ef7853405c9b07ad614fb29b95
We're not testing these anyways; building new firmware for them is not helpful.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telefire*: Do voltage tests in decivolts instead of ADC units2018-06-01T05:39:45+00:00Keith Packardkeithp@keithp.com2018-06-01T05:39:45+00:00urn:sha1:99642f9c4f89aa5577376a9cd118e7cff26e2762
This requires that each pad device specify the ADC reference voltage
and all relevant voltage divider resistor values explicitly so that
the ADC values can be converted to decivolts and compared with one
another. This should be easier to understand in the future when
reading the code.
Signed-off-by: Keith Packard <keithp@keithp.com>
Switch from GPLv2 to GPLv2+2016-07-12T22:41:41+00:00Keith Packardkeithp@keithp.com2016-07-05T16:03:49+00:00urn:sha1:1085ec5d57e0ed5d132f2bbdac1a0b6a32c0ab4a
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Add pad support for new telefire versions2016-04-20T03:21:30+00:00Keith Packardkeithp@keithp.com2015-12-18T03:30:35+00:00urn:sha1:26ce7a9a213bdd35a13937054988e7b8fa749632
Makes the voltage divider values configurable, and allows for pyro
channels that don't have the resistors necessary to check for a stuck
relay.
Also supports STM32L processors with wider GPIO registers, and uses
the new ao_gpio_set/clr_bits functions to fire igniters rather than
cc1111-specific code.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Call ao_telemetry_reset_interval when telemetry rate changes2014-07-05T07:38:09+00:00Keith Packardkeithp@keithp.com2014-07-05T07:09:25+00:00urn:sha1:ea5887027e7a39da2b7d84a142d74950b7a24703
This lets the radio code adjust the telemetry packet sending pattern
when the data rate changes.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telefire-v0.1: Use same LED selection as the v0.2 setup2013-06-22T07:53:38+00:00Keith Packardkeithp@keithp.com2013-06-22T07:53:38+00:00urn:sha1:2568b36ae9d38ae1607ec08b84b06e0fe84bd3ba
Signed-off-by: Keith Packard <keithp@keithp.com>
altos/telefire: Add siren/strobe support2012-10-10T21:28:07+00:00Keith Packardkeithp@keithp.com2012-10-10T21:28:07+00:00urn:sha1:3f059f8878a79b3154a19b6803fbc367eda80dc9
This also involved hacking up the code to allow for non-zero offsets
for the pad firing and continuity pins.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Allow sharing of radio DMA with aes engine2012-08-26T16:43:34+00:00Keith Packardkeithp@keithp.com2012-08-26T16:43:34+00:00urn:sha1:89f1a685a02c7808cf03853aa9a5ee50c6baf49e
otherwise, telefire doesn't have enough DMA channels.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Configure telefire SPI and LEDs correctly2012-08-24T07:46:55+00:00Keith Packardkeithp@keithp.com2012-08-24T07:46:55+00:00urn:sha1:7ecb429fe4682faf209452b1738ff3c8096fc5d5
This places the telefire SPI bus on USART1 option 2 and
marks the various LED functions with symbolic names.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Add telefire-v0.12012-07-30T02:47:42+00:00Keith Packardkeithp@keithp.com2012-07-30T02:44:56+00:00urn:sha1:843fcab46d633e5bb6959286adeb68e41a4c30a3
Signed-off-by: Keith Packard <keithp@keithp.com>