mjb/altos/src/drivers, branch telelaunchtwo

altos: Use simpler debounce logic for buttons

2015-12-26T04:46:40+00:00

Instead of waiting for a while after the transition to decide if it has stuck, signal the event right away and then ignore other transitions for the debounce interval. This seems to work just as reliably, but has the benefit of eliminating button latency at press time. Signed-off-by: Keith Packard

altos: Add ao_lco_two.c; alternate LCO interface code

2015-12-26T04:35:38+00:00

The LCO interface is likely to end up very device specific as the interactions depends on the input devices. Here's a version for TeleLCOTwo, which has two arming switches and a firing button. Signed-off-by: Keith Packard

altos: Allow for pad boxes with different sensor configurations

2015-12-24T07:12:18+00:00

This allows for a pad box without a resistor from power to each FET. That resistor is needed to detect welded relays, but in a solid-state system, that's not a possibility. Signed-off-by: Keith Packard

altos: Add pad support for new telefire versions

2015-12-24T07:12:18+00:00

Makes the voltage divider values configurable, and allows for pyro channels that don't have the resistors necessary to check for a stuck relay. Also supports STM32L processors with wider GPIO registers, and uses the new ao_gpio_set/clr_bits functions to fire igniters rather than cc1111-specific code. Signed-off-by: Keith Packard

altos: Support telefire products in cc1200 driver

2015-12-24T07:12:18+00:00

Need to disable the pad code while testing the radio. Signed-off-by: Keith Packard

telelco: Fix pad reset to one on radio signal loss

2015-10-13T20:54:28+00:00

The pad number was getting reset back to one when signal was lost, causing pad one to get fired in this case even when already set to arm mode. Signed-off-by: Keith Packard

altos/telelco: Adjust drag race UI

2015-10-13T20:54:28+00:00

Enter/leave drag race is done by rotating the box selector knob to a new 'dr' position and then holding down the firing button; this avoids a potential accidental firing if you somehow don't realize you've armed the box before selecting drag race mode. Signed-off-by: Keith Packard

altos/telelco: Add drag race UI

2015-08-30T00:32:54+00:00

With the unit disarmed, press and hold the fire button for five seconds to enable drag race mode. The display will show 'dr' for five seconds and beep five times to indicate that drag race mode is enabled. The decimal points in the display will all be displayed as an additional visual aid. Once every five seconds, it will beep. With drag race mode enabled, you can select a box/pad pair and press the 'fire' button to add it to the drag race group. For the current box, all members of the drag race group will have their continuity LEDs blink slowly. There will be no indication of continuity in this mode; you'll want to check that before enabling drag race mode. If you want to de-select a member of the group, just press the fire button again. Each time you push the fire button, it will beep out the pad number added or removed. Arm the box and you will not be able to add or remove members from the drag race group. Firing will simultaneously fire all members of the drag race group. To disable drag race mode, press and hold the fire button for two seconds. It will beep twice and turn off the decimal points in the display. Signed-off-by: Keith Packard

altos/telelco: Infrastructure changes for drag racing

2015-08-29T20:21:19+00:00

This makes the lco management code support arming multiple pads and firing all of them at once. The UI code does not expose this yet. Signed-off-by: Keith Packard

altos: Provide direct segment driving interface for LCD displays

2015-08-29T20:20:16+00:00

This exposes a simple bit-mask for setting the seven segments instead of just allowing hex-decimal values. Signed-off-by: Keith Packard