mjb/altos/src/drivers, branch debian/1.6.2-1

altos: Add TeleMega v2.0, including PWM driver

2015-12-26T04:48:23+00:00

Signed-off-by: Keith Packard

telelco: Fix pad reset to one on radio signal loss

2015-10-13T20:54:28+00:00

The pad number was getting reset back to one when signal was lost, causing pad one to get fired in this case even when already set to arm mode. Signed-off-by: Keith Packard

altos/telelco: Adjust drag race UI

2015-10-13T20:54:28+00:00

Enter/leave drag race is done by rotating the box selector knob to a new 'dr' position and then holding down the firing button; this avoids a potential accidental firing if you somehow don't realize you've armed the box before selecting drag race mode. Signed-off-by: Keith Packard

altos/telelco: Add drag race UI

2015-08-30T00:32:54+00:00

With the unit disarmed, press and hold the fire button for five seconds to enable drag race mode. The display will show 'dr' for five seconds and beep five times to indicate that drag race mode is enabled. The decimal points in the display will all be displayed as an additional visual aid. Once every five seconds, it will beep. With drag race mode enabled, you can select a box/pad pair and press the 'fire' button to add it to the drag race group. For the current box, all members of the drag race group will have their continuity LEDs blink slowly. There will be no indication of continuity in this mode; you'll want to check that before enabling drag race mode. If you want to de-select a member of the group, just press the fire button again. Each time you push the fire button, it will beep out the pad number added or removed. Arm the box and you will not be able to add or remove members from the drag race group. Firing will simultaneously fire all members of the drag race group. To disable drag race mode, press and hold the fire button for two seconds. It will beep twice and turn off the decimal points in the display. Signed-off-by: Keith Packard

altos/telelco: Infrastructure changes for drag racing

2015-08-29T20:21:19+00:00

This makes the lco management code support arming multiple pads and firing all of them at once. The UI code does not expose this yet. Signed-off-by: Keith Packard

altos: Provide direct segment driving interface for LCD displays

2015-08-29T20:20:16+00:00

This exposes a simple bit-mask for setting the seven segments instead of just allowing hex-decimal values. Signed-off-by: Keith Packard

altos/telefire: No reply for ARMED. Ignore time for FIRE.

2015-08-29T20:18:46+00:00

This will let us do drag races by letting the LCO arm multiple boxes and fire them all with a single command. Signed-off-by: Keith Packard

altos: Add HAS_COMPANION to new boards with companion connectors

2015-08-21T06:08:17+00:00

Thanks much to Rob Derstadt for discovering this bug! TeleMetrum v2.0, TeleMega, EasyMega, TeleBalloon v2.0 all have companion connectors and yet HAS_COMPANION was not defined. This disabled companion telemetry packets on these products, but otherwise didn't have any effect. Signed-off-by: Keith Packard

altos/telelco: Show box voltage with pad knob instead of firing button

2015-05-25T23:26:01+00:00

Turn left past '1' and see the firing box battery voltage instead of pushing the firing button with the box disarmed. This seems like a safer UI. Signed-off-by: Keith Packard

altos/telelco: Display telefire battery voltage

2015-05-25T22:49:21+00:00

When the firing button is pressed while unarmed, show the telefire battery voltage in the display. Signed-off-by: Keith Packard