mjb/altos/src/drivers/ao_cc115l.c, branch 1.4.9.3AltOS - the operating system for Altus Metrum products
https://git.ethernal.org/mjb/altos/atom?h=1.4.9.32014-09-07T03:39:37+00:00altos: Reduce deviation at 2400/9600 baud2014-09-07T03:39:37+00:00Keith Packardkeithp@keithp.com2014-09-07T03:39:37+00:00urn:sha1:f395bcaa620490954d4a42de9b4870bc12bedc91
There's no reason to use 20.5kHz deviation at 2400 and 9600 baud, and
if we get a better receiver, we'll want to use narrower deviation to
have less bandwidth sucking noise into the radio. The new values are
(nominally) 5.125kHz deviation for 9600 baud and 1.5kHz deviation for
2400 baud.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Add 2400 and 9600 baud telemetry support to cc115l driver2014-07-05T07:38:10+00:00Keith Packardkeithp@keithp.com2014-07-03T05:41:20+00:00urn:sha1:8935e29e5aa9c01cd00b275a35dd7b99c00980c3
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Allow cc115l driver to be built without radio power control2014-06-06T00:24:57+00:00Keith Packardkeithp@keithp.com2014-06-06T00:24:57+00:00urn:sha1:2db2b75f8847ca0066bb19771653a65c9098ae52
TeleGPS just wants full power, so remove the configuration option
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Fix cc115l debug build2014-05-21T08:43:12+00:00Keith Packardkeithp@keithp.com2014-05-21T08:35:33+00:00urn:sha1:8b488bdd0f5c91be7e5aae1c8f0193e713734b14
New compiler warning flags and moving to the nxp require a few minor
changes in the code to make it work.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: cc115l driver tone_run wasn't recording number of tones2013-12-21T06:59:42+00:00Keith Packardkeithp@keithp.com2013-12-21T06:59:42+00:00urn:sha1:48f996a9d65631238b4de446530f31f83acb99f5
This would prevent the cc115l driver from ever sending tones.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Clean up warnings for LPC products2013-12-21T06:59:35+00:00Keith Packardkeithp@keithp.com2013-12-21T06:58:10+00:00urn:sha1:e11fcc299f4a1a0461a3442ca13f8984d76c30ff
Unused varibles, functions and parameters.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: various cc115l driver hacks2013-08-20T15:54:44+00:00Keith Packardkeithp@keithp.com2013-08-20T15:54:44+00:00urn:sha1:e2f385946132690ca6dc141d7c7830ae0cfe3458
Try to recover from TX_FIFO_UNDERFLOW by resetting the chip at idle
time.
Do a calibration phase during setup.
Program power to ramp up to limit key down noise.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Remove ao_radio_gpio_bits from normal build2013-07-03T00:55:24+00:00Keith Packardkeithp@keithp.com2013-06-24T21:29:43+00:00urn:sha1:d95a2c5d1ddce913dcb1d1ab5dc59f6a588ab599
Only needed for the CC115L_TRACE code, and it only builds on STM
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Set APRS deviation to 3kHz2013-05-08T03:08:01+00:00Keith Packardkeithp@keithp.com2013-05-06T23:08:52+00:00urn:sha1:3876b5bfad383119339aea51e2cf301012a1f991
I finally found a bunch of references to APRS on the net and they all
appear to assume a 3kHz deviation. Let's see if this works better with
Yaesu radios.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Make sure the packet format is set reasonably for radio test2013-04-12T10:09:16+00:00Keith Packardkeithp@keithp.com2013-04-12T10:09:16+00:00urn:sha1:679401fff981b675dd5a188c64e8940254588800
Dunno if this matters, but it might as well be set reasonably
Signed-off-by: Keith Packard <keithp@keithp.com>