mjb/altos/altosdroid, branch 1.6.0.3AltOS - the operating system for Altus Metrum products
https://git.ethernal.org/mjb/altos/atom?h=1.6.0.32015-06-24T05:21:45+00:00altosdroid: Update version numbers in manifest2015-06-24T05:21:45+00:00Keith Packardkeithp@keithp.com2015-06-24T05:21:45+00:00urn:sha1:3ce5e24fefaddaa74eadba4722e904354c871387
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Mark tab-dependent voice output as done2015-06-24T05:21:30+00:00Keith Packardkeithp@keithp.com2015-06-24T05:21:30+00:00urn:sha1:d9f96c45d0a3099e9e5fd3c75cc27f9415fcaf55
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Make sure flight voice output always starts with 'speed'2015-06-24T05:04:47+00:00Keith Packardkeithp@keithp.com2015-06-24T05:04:47+00:00urn:sha1:aed8d3ee2561bbec59b9684fb2042186191302ca
This resets the flight-mode voice output state back to start again
each time the flight tab is selected
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Make sure whole flight state is spoken even when no-one is moving2015-06-24T05:00:33+00:00Keith Packardkeithp@keithp.com2015-06-24T05:00:33+00:00urn:sha1:b1b41e0823a60769e7d2d806f4d97ae043d7dae3
This eliminates the case where much of the flight state wasn't
reported if the tracker or receiver weren't moving.
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Change voice output around2015-06-24T04:42:35+00:00Keith Packardkeithp@keithp.com2015-06-24T04:39:09+00:00urn:sha1:bfa6cd8934b993bd4a67cfc7a4eeecf9b11915ef
This makes the voice output depend on the current displayed tab; where
the 'recovery' and 'map' tabs get the same value.
Pad
Reports igniter and GPS status changes
Flight
Report flight state changes and max height after apogee
Report current speed, height and bearing/elevation/range once
every 10 seconds while the rocket is in motion.
Recovery
Report distance and bearing when the location of either the
tracker or the receiver changes by more than 10m, but not more
than once every 10 seconds.
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Define strings for the tab names2015-06-24T04:42:35+00:00Keith Packardkeithp@keithp.com2015-06-24T04:37:25+00:00urn:sha1:a761b34ed8fc64435f5a49623f4a5c55e2dda33a
Use these everywhere instead of replicating the same name; might
reduce errors.
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Show direction to target in recover tab2015-06-24T04:42:35+00:00Keith Packardkeithp@keithp.com2015-06-24T04:35:43+00:00urn:sha1:56146cd379e1319b7adcf8e22cdda55f771e11be
This takes the bearing to target and current direction of motion (from
the Android API) and computes a turn amount and displays that so you
don't have to know which way is north when walking towards the rocket.
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Fix line drawing to old tracker location2015-06-23T06:21:05+00:00Keith Packardkeithp@keithp.com2015-06-23T06:21:05+00:00urn:sha1:1513693602c2a4cab0783833d1844c066edabb71
Selecting an old tracker would often fail to switch the bearing line
as it was using the map data instead of just using the local data for
the relavant tracker.
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Mark four-tab change done2015-06-23T04:04:44+00:00Keith Packardkeithp@keithp.com2015-06-23T04:04:01+00:00urn:sha1:87d2ab135b493486162d33ff172eba1f44dc0ce5
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Allow tracker selection from online map widget2015-06-23T04:04:43+00:00Keith Packardkeithp@keithp.com2015-06-23T03:59:17+00:00urn:sha1:fb0bd0ec18088ef01549cdb96243d591f618e32b
Need separate tracker selection code for online maps
Signed-off-by: Keith Packard <keithp@keithp.com>