mjb/altos/altosdroid/src/org/altusmetrum/AltosDroid/AltosVoice.java, branch telemega-v2AltOS - the operating system for Altus Metrum products
https://git.ethernal.org/mjb/altos/atom?h=telemega-v22015-10-13T20:54:28+00:00altoslib: Clean up remaining direct AltosState.state users2015-10-13T20:54:28+00:00Keith Packardkeithp@keithp.com2015-09-21T05:32:52+00:00urn:sha1:431c713389dc819d2433d893c898ff82c7941722
This value has been hidden to avoid having it written accidentally;
there were a few more bits of code using it though.
Signed-off-by: Keith Packard <keithp@keithp.com>
Bump Java library versions2015-07-16T01:31:05+00:00Keith Packardkeithp@keithp.com2015-07-16T01:31:05+00:00urn:sha1:d6445b3739ac2c5dd040efdb97317a6b2a48044a
Avoid problems if you have an old version of the library installed
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Remove a debug line in AltosVoice2015-07-12T02:54:07+00:00Keith Packardkeithp@keithp.com2015-07-12T02:54:07+00:00urn:sha1:bdc953e26ac2dd67021f905807324c6a02e49690
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Make sure flight voice output always starts with 'speed'2015-06-24T05:04:47+00:00Keith Packardkeithp@keithp.com2015-06-24T05:04:47+00:00urn:sha1:aed8d3ee2561bbec59b9684fb2042186191302ca
This resets the flight-mode voice output state back to start again
each time the flight tab is selected
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Make sure whole flight state is spoken even when no-one is moving2015-06-24T05:00:33+00:00Keith Packardkeithp@keithp.com2015-06-24T05:00:33+00:00urn:sha1:b1b41e0823a60769e7d2d806f4d97ae043d7dae3
This eliminates the case where much of the flight state wasn't
reported if the tracker or receiver weren't moving.
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Change voice output around2015-06-24T04:42:35+00:00Keith Packardkeithp@keithp.com2015-06-24T04:39:09+00:00urn:sha1:bfa6cd8934b993bd4a67cfc7a4eeecf9b11915ef
This makes the voice output depend on the current displayed tab; where
the 'recovery' and 'map' tabs get the same value.
Pad
Reports igniter and GPS status changes
Flight
Report flight state changes and max height after apogee
Report current speed, height and bearing/elevation/range once
every 10 seconds while the rocket is in motion.
Recovery
Report distance and bearing when the location of either the
tracker or the receiver changes by more than 10m, but not more
than once every 10 seconds.
Signed-off-by: Keith Packard <keithp@keithp.com>
altoslib/altosuilib: Update library version to 72015-05-26T03:34:05+00:00Keith Packardkeithp@keithp.com2015-05-26T03:34:05+00:00urn:sha1:cb23b992be8ba40c97d8988c134a814a13ccd58c
So many ABI/API changes
Signed-off-by: Keith Packard <keithp@keithp.com>
Bump java library versions2015-02-08T04:42:15+00:00Keith Packardkeithp@keithp.com2015-02-08T04:42:15+00:00urn:sha1:4231d68bae69d9a7d1f52205002db452cd5f986d
Lots of minor API/ABI changes; make sure people can install both 1.5
and 1.6 at the same time.
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Add imperial unit support2014-09-06T07:37:57+00:00Keith Packardkeithp@keithp.com2014-09-06T07:14:26+00:00urn:sha1:18671803d078aa798b603c67b741c3ba4374f41d
Provides a menu entry to switch units, changes all value displays to
use the AltosLib units conversion code.
Signed-off-by: Keith Packard <keithp@keithp.com>
altosdroid: Use single object to pass data to UI2014-09-04T05:32:49+00:00Keith Packardkeithp@keithp.com2014-09-04T05:32:49+00:00urn:sha1:3842735e303f0bf6f46ed8cb659c92d8bb9bd137
Instead of having separate messages for each piece of telemetry state,
package the whole mess up in one object and send it for any
change. This simplifies tracking within the UI by avoiding corner
cases during reconnect.
Signed-off-by: Keith Packard <keithp@keithp.com>