mjb/altos, branch telelaunchtwoAltOS - the operating system for Altus Metrum products
https://git.ethernal.org/mjb/altos/atom?h=telelaunchtwo2015-12-26T04:46:40+00:00altos: Use simpler debounce logic for buttons2015-12-26T04:46:40+00:00Keith Packardkeithp@keithp.com2015-12-26T04:46:40+00:00urn:sha1:d312808f20e9358e1eca94dc7f747928d4ee85b1
Instead of waiting for a while after the transition to decide if it
has stuck, signal the event right away and then ignore other
transitions for the debounce interval.
This seems to work just as reliably, but has the benefit of
eliminating button latency at press time.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Add ao_lco_two.c; alternate LCO interface code2015-12-26T04:35:38+00:00Keith Packardkeithp@keithp.com2015-12-25T19:26:34+00:00urn:sha1:3eca6e02e022e184e98d945368d0a8cf22f54049
The LCO interface is likely to end up very device specific as the
interactions depends on the input devices. Here's a version for
TeleLCOTwo, which has two arming switches and a firing button.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Add easy mini plotting helper in test code2015-12-24T07:15:16+00:00Keith Packardkeithp@keithp.com2015-12-24T07:15:16+00:00urn:sha1:ea862c76aec383f8b802511cbfa81e7566e82062
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Fix telefiretwo .gitignore2015-12-24T07:12:18+00:00Keith Packardkeithp@keithp.com2015-12-22T05:52:31+00:00urn:sha1:bf73b27c167d3a75645d996b8cfafe4f48d16d94
Was ignoring the wrong built files
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Add TeleLCOTwo firmware2015-12-24T07:12:18+00:00Keith Packardkeithp@keithp.com2015-12-22T05:50:43+00:00urn:sha1:ab6a8b63ec77436cf7e939c7dcf836ac8817c615
The LCO side of a two-channel launch controller setup.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Support pad/lco boxes with fixed box numbers2015-12-24T07:12:18+00:00Keith Packardkeithp@keithp.com2015-12-22T05:48:37+00:00urn:sha1:c32c39a2290ac76cd4e85702d981babdbaf5f72d
This allows for a configuration without adjustable box numbers on
either end of the link, simplifying the UI.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Allow for pad boxes with different sensor configurations2015-12-24T07:12:18+00:00Keith Packardkeithp@keithp.com2015-12-22T05:47:10+00:00urn:sha1:179f54b60f9e511dc664a35223d9126352ec8f15
This allows for a pad box without a resistor from power to each
FET. That resistor is needed to detect welded relays, but in a
solid-state system, that's not a possibility.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: telefiretwo-v0.1 bits2015-12-24T07:12:18+00:00Keith Packardkeithp@keithp.com2015-12-18T03:54:23+00:00urn:sha1:57648595285d9c710631da18714a3f070c70baa3
Get this board running.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Add pad support for new telefire versions2015-12-24T07:12:18+00:00Keith Packardkeithp@keithp.com2015-12-18T03:30:35+00:00urn:sha1:d5901b4dd25a5988d3ee3ebb17cf78f4a5bb74ad
Makes the voltage divider values configurable, and allows for pyro
channels that don't have the resistors necessary to check for a stuck
relay.
Also supports STM32L processors with wider GPIO registers, and uses
the new ao_gpio_set/clr_bits functions to fire igniters rather than
cc1111-specific code.
Signed-off-by: Keith Packard <keithp@keithp.com>
altos: Support telefire products in cc1200 driver2015-12-24T07:12:18+00:00Keith Packardkeithp@keithp.com2015-12-18T03:29:36+00:00urn:sha1:466917ca8bd55f68e2f26b718ed3e55fd4b6f2c7
Need to disable the pad code while testing the radio.
Signed-off-by: Keith Packard <keithp@keithp.com>